The Simple Stability Problems Study Unit, "MEPE", has been designed to study the stability of a bar subjected to buckling by obtaining the critical load in different configurations. The unit consists of two bars of same length connected by a...

The Laminar Flow Visualization and Analysis Unit, "LFA", allows a complete study of the two-dimensional problems associated with the laminar flow by the visualization of the different models of flow, which can be observed thanks to an efficient...

The Gear Generation Unit, "MGE", has been designed by EDIBON to study rack and pinion systems. With this unit the student can draw by an easy procedure the profile of a tooth, produced by the involute process of the rack when passing over the...

Tidal energy is another way to generate electricity extracting energy from the sea. Twice a day big volumes of water rise and fall with the tides.A Tidal Barrage make use of the potential energy in the difference in height (or head) between high...

It includes a Cut away DC compound excitation motor-generator (EMT4-S) in order to study the different parts of this motor type.

It includes a Cut away DC shunt-series compound excitation motor (EMT5-S) in order to study the different parts of this motor type.

It includes a Cut away DC series excitation motor-generator (EMT2-S) in order to study the different parts of this motor type.

It includes a Cut away DC independent excitation motor-generator (EMT1-S) in order to study the different parts of this motor type.

With the Direct Current (DC) Circuits Kit, "M1/KIT", designed by EDIBON, you can begin to study the basic principles of direct current.

The Journal Bearing Unit, "MPCO", allows to study the pressure distribution in sliding bearings. It illustrates the principle of hydrodynamic lubrication.The unit is mounted on a metallic structure assembled on wheels for its mobility.The sliding...

The GPS Unit, "EGPS", designed by EDIBON, has been developed for the study of basic concepts about global positioning systems. The unit allows to acquire a solid knowledge about how a GPS receiver works, not needing any prior knowledge.The "EGPS"...

The Ground Water Flow Unit, "EFAS", is composed of a test tank that will be filled with fine grave or sand to construct to develop different models. The entry of water into the tank is done through two inlets, each of them located at each end. The...

This unit is common for Heat Exchangers type "TI" and can work with one or several exchangers.This unit performs the following tasks:Heating water in a computer controlled thermostatic bath.Pumping the hot water.Regulation and measurement of the...

With Digital Electronic Fundamentals Kit, "M11/KIT", designed by EDIBON, numbering systems, logic circuits, TTL gates, CMOS, Boolean algebra, etc. can be studied.

The Basic Luminosity Control Application, "AEL-AD6B", has been designed by EDIBON to study how a luminosity control application works. This unit is composed by several modules in order to carry out practices related to switching circuits to...

With Basic Combinational Circuits Kit, "M12/KIT", designed by EDIBON, encoders, decoders, multiplexers, demultiplexers, digital comparators and arithmetic and logical operations can be studied.

With Basic Sequential Circuits Kit, "M13/KIT", designed by EDIBON, all types of bistables, counters, flip-flops, synchronous sequential circuits and the operation of memories can be studied.

The Basic Teaching Unit for the Study of Regulation and Control, "RYC/B", allows the user to learn the basics about regulation and control of first and second order systems.This unit enables to carry a set of practices related with basic...

The Gyroscope, "MGI", allows the experimental demonstration of the different rotation modes of a gyroscope and the moments generated by the gyroscopic effect. The rotor of the electric motor (rotating motor) shares a horizontally supported shaft...

With Semiconductors I Kit, "M3/KIT", designed by EDIBON, the basic concepts of diodes can be studied, at the same time as the student will be asked to carry out a series of assemblies on the practice board to consolidate his knowledge of PN-type...

With Semiconductors II Kit, "M4/KIT", designed by EDIBON, semiconductors can be studied by extending the knowledge acquired in the basic module "M3/KIT".

The "THER" consists of a refrigeration circuit, with the most common heat exchangers in refrigeration circuits. All the elements are clearly mounted in the front panel of the unit. The evaporator is an air cooling finned tube heat exchanger and a...

The High Voltage Laboratory System "HVLS" is formed by a base unit and three optional test kits some optional made with highest precision to build different configurations in order to carry out high AC Voltage Tests, DC Voltage Tests and Impulse...

The Dutch Vat for Cheese Production (up to 50 l), "DVCP", has a tank with water jacket, coil with inlet and outlet for water from the boiler, jacket water inlet, serum drainage valve and set of accessories for the agitation, cutting and drain of...

The Computer Controlled Tray Drier "SBANC" is a laboratory scale unit designed to study fluid mechanics, surface chemistry, solids structures and mass and energy balances related to the drying process.It consists of a tunnel, several trays where...

The Osborne Reynolds Horizontal Demonstration Unit, "FME31", designed by EDIBON, allows to study the characteristics of a liquid flowing through a pipe and the Reynolds number in each of the liquid states.The FME31 unit makes it possible to study...

The Hydraulic and Electro-Hydraulic Application, "AE-HD", is a modular unit consisting of a great variety of optional kits and elements to configure the desired Hydraulic and Electro-Hydraulic circuit.The optional hydraulic kits available with the...

The Hydraulic Radiator Balancing Training Unit, "THBT", allows the study of the amount of water with which to guarantee that all the radiators of an installation are supplied with sufficient hot water.The hydraulic balancing is carried out by...