7.4.- INSTALLATIONS AND MAINTENANCE

The needs of today's society are a challenge for any industry, since they have to be in continuous evolution and renewal to adapt to those needs.

View more

In recent years, as a result of the new industrial revolution or "Industry 4.0", the emergence of the "Industrial Internet of Things" ("IIoT") and the "Smart Factories", that adaptation is possible thanks to the application of the most sophisticated techniques in the design of new facilities or in the renovation of existing ones.

In spite of all these technological advances and the exhaustive controls carried out, it should not be forgotten that any element that take part in the productive process is going to be subjected to a mechanical and electrical wear (efforts, loads, etc.) and its useful life is limited. To avoid catastrophic failures, stoppages in production or any type of process that implies an increase of non-productive times and, therefore, an increase of costs, it is extremely important to carry out a good maintenance of machinery, electrical systems, etc.

Traditionally, only two types of maintenance were considered:

  • Corrective: the fault is solved once it has already occurred.
  • Preventive: periodic review of all those problematic elements and their replacement if required.

These types of maintenance involve very high and unnecessary costs in most cases. Nowadays, thanks to the available technology, it is possible to carry out predictive maintenance consisting of a comprehensive analysis of all those variables that take part in all the components of a system and be able to replace them at the right time.

But, if more control over the failures that can suffer all those mechanical components subject to wear is preferred, there is another type of maintenance, known as proactive maintenance. It goes one step further than the predictive maintenance, looking for the root of the problem.

View Products

INSTALLATIONS AND MAINTENANCE EQUIPMENT

1.- PHYSICS 2.- ELECTRONICS 3.- COMMUNICATIONS 4.- ELECTRICITY 5.- ENERGY 6.- MECHATRONICS & AUTOMATION 7.- MECHANICS 8.- FLUID MECHANICS 9.- THERMODYNAMICS & THERMOTECHNICS 10.- PROCESS CONTROL 11.- CHEMICAL ENGINEERING 12.- FOOD & WATER TECHNOLOGIES 13.- ENVIRONMENT 14.- BIOMEDICAL ENGINEERING LABORATORY ACCESSORIES CUSTOMIZED PILOT PLANTS
7.1.- MECHANICAL ENGINEERING 7.2.- AUTOMOTIVE MECHANICAL ENGINEERING 7.3.- MATERIALS ENGINEERING 7.4.- INSTALLATIONS AND MAINTENANCE
7.4.1.- CUTAWAY MODELS 7.4.2.- DETACHABLE MODELS 7.4.3.- INSTALLATIONS AND MAINTENANCE TRAINING
There are not subgroup available
Showing 31-37 of 37 item(s)
12 24 36
SET OF ELECTROMECHANICAL VIBRATIONS - MDU-SEV
  • Accessory of MDU
Available
7.4.3.- INSTALLATIONS AND MAINTENANCE TRAINING

MDU-SEV

Set of Electromechanical Vibrations

Accessory of MDU
Among the drive systems are the asynchronous motors, which generate vibrations in machines.This is the case with an asymmetric air gap (space between rotor and stator), in which the magnetic vibrational forces induce torsional and bending...
View Unit
DISPLACEMENT SENSORS FOR MDU UNIT - MDU-SD
  • Accessory of MDU
Available
7.4.3.- INSTALLATIONS AND MAINTENANCE TRAINING

MDU-SD

Displacement Sensors for MDU Unit

Accessory of MDU
Two displacement sensors which, together with the Set of Elastic Shaft ,"MDU-SES", and the Software, Sensors and Control for MDU Unit, "MDU-SSC", allow you to represent subcritical and supercritical shaft orbits in resonance.
View Unit
SCREW JOINT TESTING UNIT - MSCT
  • MSCT
Available
7.4.3.- INSTALLATIONS AND MAINTENANCE TRAINING

MSCT

Screw Joint Testing Unit

The Screw Joint Testing Unit, "MSCT", represents the simulation of a tightening set consisting of a screw and a nut on two rectangular shaped beams.A very precise torque wrench performs the tightening through a threaded rod and a flywheel. The...
View Unit
UNIT TO STUDY LATHE GEARS - MSLG
  • MSLG
Available
7.4.3.- INSTALLATIONS AND MAINTENANCE TRAINING

MSLG

Unit to Study Lathe Gears

The Unit to Study Lathe Gears, "MSLG", represents the gears of a typical lathe in a machining workshop, including: a main adjustable transmission gear, one Norton gearbox for the machining of specific threads and pitches, a pinion switching gear...
View Unit
BASIC UNIT OF MECHANICAL DRIVE SYSTEMS - MDSU
  • MDSU
Available
7.4.3.- INSTALLATIONS AND MAINTENANCE TRAINING

MDSU

Basic Unit of Mechanical Drive Systems

The Basic Unit of Mechanical Drive Systems, "MDSU", consists of a main frame where a series of accessories and elements are arranged, distributed in modules of different level, thought to introduce the user in the field of mechanical systems and...
View Unit
RIGGING TRAINING UNIT - RGT
  • RGT
Available
7.4.3.- INSTALLATIONS AND MAINTENANCE TRAINING

RGT

Rigging Training Unit

The Rigging Training Unit, "RGT", has been designed for the study of techniques to move loads of various shapes, sizes and types safely. The unit consists of an adjustable height gantry frame made of welded steel and beam attachment points. The...
View Unit
Ask for information