14.1.3.- STATICS AND DYNAMICS

STATICS AND DYNAMICS UNITS

1.- PHYSICS 2.- ELECTRONICS 3.- COMMUNICATIONS 4.- ELECTRICITY 5.- ENERGY 6.- MECHATRONICS & AUTOMATION 7.- MECHANICS 8.- FLUID MECHANICS 9.- THERMODYNAMICS & THERMOTECHNICS 10.- PROCESS CONTROL 11.- CHEMICAL ENGINEERING 12.- FOOD & WATER TECHNOLOGIES 13.- ENVIRONMENT 14.- BIOMEDICAL ENGINEERING LABORATORY ACCESSORIES CUSTOMIZED PILOT PLANTS
14.1.- BIOMECHANICS 14.2.- BIOMEDICAL ELECTRONICS 14.3.- BIOMEDICAL EQUIPMENT
14.1.1.- MECHANICS FUNDAMENTALS KITS 14.1.2.- SIMPLE MACHINES 14.1.3.- STATICS AND DYNAMICS 14.1.4.- VIBRATIONS AND OSCILLATIONS 14.1.5.- TRIBOLOGY (FRICTION, WEAR, LUBRICATION) 14.1.6.- STRUCTURAL MECHANICS 14.1.7.- PHOTOELASTICITY AND STRAIN MEASUREMENT 14.1.8.- MECHANICAL TESTS 14.1.9.- THERMAL AND ACOUSTIC TESTS
There are not subgroup available
Showing 1-15 of 15 item(s)
12 24 36
UNIT FOR STUDYING EQUILIBRIUM OF MOMENTS ON A TWO ARM LEVER - MEMB2
  • MEMB2
Available
7.1.3.- STATICS AND DYNAMICS

MEMB2

Unit for studying Equilibrium of Moments on a Two Arm Lever

The Unit for studying Equilibrium of Moments on a Two Arm Lever,"MEMB2", allows to study the fundamentals of the equilibrium of moments and the application of the law of levers on a two-arm lever.A pivoted beam in the extreme of a vertical support...
View Unit
COMPUTER CONTROLLED BALANCE OF RECIPROCATING MASSES UNIT - MBMRC
  • MBMRC
Available
7.1.3.- STATICS AND DYNAMICS

MBMRC

Computer Controlled Balance of Reciprocating Masses Unit

The Computer Controlled Balance of Reciprocating Masses Unit, "MBMRC", is a bench-mounting unit that allows to investigate and examine the free masses and moments of a reciprocating engine with a single cylinder, with two cylinders or with four...
View Unit
CAM ANALYSIS UNIT - MEAL
  • MEAL
Available
7.1.3.- STATICS AND DYNAMICS

MEAL

Cam Analysis Unit

The Cam Analysis Unit "MEAL" allows to observe the effect of the profile of a cam, the study of the displacement, velocity and acceleration profiles of the cam and the identification of the factors that can modify the dynamics of the cam. This...
View Unit
CORIOLIS FORCE DEMONSTRATION UNIT - MDFC
  • MDFC
Available
7.1.3.- STATICS AND DYNAMICS

MDFC

Coriolis Force Demonstration Unit

The Coriolis Force Demonstration Unit, "MDFC", is used to observe the deflection of a jet of water generated by a pump attached to a rotating arm that rotates to different speeds in a horizontal plane. An electronically controlled motor rotates...
View Unit
CENTRIFUGAL FORCE UNIT - MFCE
  • MFCE
Available
7.1.3.- STATICS AND DYNAMICS

MFCE

Centrifugal Force Unit

The Centrifugal Force Unit, "MFCE", is used to demonstrate the relationship between centrifugal force, rotational speed, mass of a rotating body and distance from the axis. The unit consists of a vertical axis of rotation and a rotating arm....
View Unit
GYROSCOPE - MGI
  • MGI
Available
7.1.3.- STATICS AND DYNAMICS

MGI

Gyroscope

The Gyroscope, "MGI", allows the experimental demonstration of the different rotation modes of a gyroscope and the moments generated by the gyroscopic effect. The rotor of the electric motor (rotating motor) shares a horizontally supported shaft...
View Unit
CENTRIFUGAL GOVERNOR UNIT - CGU
  • CGU
Available
7.1.3.- STATICS AND DYNAMICS

CGU

Centrifugal Governor Unit

The Centrifugal Governor Unit, "CGU", has been designed to study the operating mode of different centrifugal governors, including three interchangeable governors: Porter governor, Hartnell governor and Proell governor.Interchangeable governors...
View Unit
STATIC AND DYNAMIC BALANCING UNIT - MED
  • MED
Available
7.1.3.- STATICS AND DYNAMICS

MED

Static and Dynamic Balancing Unit

The Static and Dynamic Balancing Unit, "MED", developed by EDIBON is a unit to study and analyze the oscillations and vibrations and how to eliminate or diminish them.Basically, the unit is formed by a shaft mounted on bearings. The shaft is...
View Unit
SIMPLE BALANCING UNIT - MES
  • MES
Available
7.1.3.- STATICS AND DYNAMICS

MES

Simple Balancing Unit

The Simple Balancing Unit, "MES", developed by EDIBON is a unit to study and analyze the oscillations and vibrations and how to eliminate or diminish them.Basically, the unit is formed by a shaft mounted on bearings. The shaft is coupled by pulley...
View Unit
INERTIA FLYWHEEL UNIT - MIF
  • MIF
Available
7.1.3.- STATICS AND DYNAMICS

MIF

Inertia Flywheel Unit

The Inertia Flywheel Unit, "MIF", consists of an inertia disc with a rotation shaft at the center of the disc.The shaft is supported at two points by bearings.A cord is attached by one of the ends to the shaft and wound around it. At the other end...
View Unit
WHEEL AND AXLE UNIT - MRYE1
  • MRYE1
Available
7.1.3.- STATICS AND DYNAMICS

MRYE1

Wheel and Axle Unit

The Wheel and Axle Unit, "MRYE1", is a unit which allows to investigate the mechanics of a simple wheel and axle machine and to demonstrate the laws of the formation of equilibrium of moments in static systems.Two pulleys with different diameter...
View Unit
WHEEL AND DIFFERENTIAL AXLE UNIT - MRYE2
  • MRYE2
Available
7.1.3.- STATICS AND DYNAMICS

MRYE2

Wheel and Differential Axle Unit

The Wheel and Differential Axle Unit, "MRYE2", is a unit that allows for investigating the mechanics of a wheel and differential axle mechanism and demonstrating the force reduction on a differential pulley block.A wheel, consisting of a pulley...
View Unit
UNIT FOR STUDYING HOOKE´S LAW - MELH
  • MELH
Available
7.1.3.- STATICS AND DYNAMICS

MELH

Unit for studying Hooke´s Law

The Unit for studying Hooke's Law, "MELH", designed by EDIBON, demonstrates the application of Hooke's Law and allows the visualization of the deformation of tension springs under load and the performance of oscillation experiments on a spring –...
View Unit
SIMPLE HARMONIC MOTION UNIT - MSHU
  • MSHU
Available
7.1.3.- STATICS AND DYNAMICS

MSHU

Simple Harmonic Motion Unit

This Simple Harmonic Motion Unit, "MSHU", allows many experiments using several pendulums and devices, such as different types of pendulums (simple, bifilar, trifilar and Kater’s pendulum) and springs.Consists of a panel with a support that allows...
View Unit
UNIT TO STUDY ROTATIONAL INERTIA - SRI
  • SRI
Available
7.1.3.- STATICS AND DYNAMICS

SRI

Unit to Study Rotational Inertia

The Unit to Study Rotational Inertia, "SRI", has been designed to carry out tests to analyze the moments of inertia of a solid and a hollow cylinder, both with same mass and diameter. The moment of inertia of another hollow cylinder with different...
View Unit
Ask for information