TECHNICAL AND VOCATIONAL EDUCATION FLUID MECHANICS LABORATORY

COMPUTER CONTROLLED KAPLAN TURBINE - TKC

TKC

Available

5.3.6.- HYDRAULIC ENERGY

TKC

Computer Controlled Kaplan Turbine

The Computer Controlled Kaplan Turbine, "TKC", consists of a small-scale Kaplan turbine that has a ring with adjustable guide vanes, which allow the control of water flow in the turbine.In order to raise the fluid, it has a computer controlled...

PRESSURE MEASUREMENT AND CALIBRATION UNIT - TMCP

TMCP

Available

8.2.- MEASUREMENT

TMCP

Pressure Measurement and Calibration Unit

The Pressure Measurement and Calibration Unit, "TMCP", has been designed to study the concept of pressure and the different methods and techniques used to measure this variable.The dead-weight calibrator consists of a cylinder in which interior a...

COMPUTER CONTROLLED PELTON TURBINE - TPC

TPC

Available

5.3.6.- HYDRAULIC ENERGY

TPC

Computer Controlled Pelton Turbine

The Computer Controlled Pelton Turbine, "TPC", designed by EDIBON, consists of a small-scale Pelton turbine, with a valve that allows the flow to be regulated. The turbine includes a PELTON runner with 16 buckets, which can be clearly seen through...

HYDROGEN BUBBLE FLOW VISUALIZATION UNIT - UVF

UVF

Available

8.4.- FLOW VISUALIZATION

UVF

Hydrogen Bubble Flow Visualization Unit

The Hydrogen Bubble Flow Visualization Unit, "UVF", is a self-contained unit designed to study different flow patterns through the hydrogen bubble flow visualization technique.Bubbles are generated by electrolysis by the application of an electric...

COMPUTER CONTROLLED FLUID FRICTION IN PIPES, WITH HYDRAULICS BENCH (FME00) - AFTC

AFTC

Available

8.8.- FLUID PIPING SYSTEM

AFTC

Computer Controlled Fluid Friction in Pipes, with Hydraulics Bench (FME00)

The Computer Controlled Fluid Friction in Pipes, with Hydraulics Bench (FME00), "AFTC", is designed to determine the friction coefficient in pipes of several diameters and roughness, to study the pressure losses and pressure development in...

COMPUTER CONTROLLED PIPE NETWORK UNIT, WITH HYDRAULICS BENCH (FME00) - AMTC

AMTC

Available

8.8.- FLUID PIPING SYSTEM

AMTC

Computer Controlled Pipe Network Unit, with Hydraulics Bench (FME00)

The Computer Controlled Pipe Network Unit, with Hydraulics Bench (FME00), "AMTC", consists of a pipe network, a lateral panel where all the elements to test are located and a hydraulics bench, which has all the elements and accessories required...

DATA ACQUISITION SYSTEM AND SENSORS - BDAS

BDAS

Available

8.1.7.- HYDRAULIC MACHINES: TURBINES

BDAS

Data Acquisition System and Sensors

BDAS is designed to monitor the measurements of each unit type "FME" from a computer (PC).This system can monitor any unit, checking the revolutions given by the water pump or the torque, differential pressures for Bernoulli theorems, pressure...

HYDROSTATICS BENCH & FLUID PROPERTIES - BHI

BHI

Available

8.3.- HYDROSTATICS

BHI

Hydrostatics Bench & Fluid Properties

The Hydrostatics Bench and Fluid Properties, "BHI", is a compact, mobile and independent unit.There is a water storage tank, to work in a closed system, at the bottom of the bench. The water is distributed by hand pumps from this tank to two upper...

SEDIMENT TRANSPORT DEMONSTRATION CHANNEL - CAS

CAS

Available

13.1.- HYDROLOGY AND HYDROGEOLOGY

CAS

Sediment Transport Demonstration Channel

The Sediment Transport Demonstration Channel, "CAS", designed by EDIBON, consist of an inclinable channel mounted on a base plate, supported by two supports, with a discharge tank and recirculating pump. This tank is in the Basic Hydraulic Feed...

COMPUTER CONTROLLED WATER HAMMER UNIT - EGAC

EGAC

Available

8.8.- FLUID PIPING SYSTEM

EGAC

Computer Controlled Water Hammer Unit

The Computer Controlled Water Hammer Unit, "EGAC", is designed to demonstrate the effects of an instantaneous variation of the speed of a fluid. It is possible to study the water hammer, which is the consequence of a quick change in a fluid speed....

FME00

Available

8.1.1.- BASE UNITS

FME00

Hydraulics Bench

The Hydraulics Bench, "FME00", designed by EDIBON, allows the study of fluid behaviour, hydraulic theory and the properties of fluid mechanics.It is formed by a movable hydraulics bench used to hold a wide variety of modules, which allow the...

FME00/B

Available

8.1.1.- BASE UNITS

FME00/B

Basic Hydraulic Feed System

The Basic Hydraulic Feed System, "FME00/B", designed by EDIBON is a service unit for different Fluid Mechanics Units as: "FME" type modules, Fluid Friction in Pipes Unit "AFT", etc., increasing the equipment profitability.

FME01

Available

8.1.4.- HYDRODYNAMICS

FME01

Jet Impact on Surfaces

The Jet Impact on Surfaces Unit, "FME01", designed by EDIBON, allows the study of the interaction between a moving fluid jet and different impact surfaces, providing a detailed understanding of fluid dynamics principles and their application in...

FME02

Available

8.1.2.- MEASUREMENT

FME02

Flow over Weirs

The Flow over Weirs, "FME02", designed by EDIBON, has many elements that are used in combination with the Hydraulics Bench (FME00): A special mouthpiece is coupled to the outlet mouthpiece for water in the Hydraulics Bench (FME00).Two soothing...

BERNOULLI'S THEOREM DEMONSTRATION - FME03

FME03

Available

8.1.4.- HYDRODYNAMICS

FME03

Bernoulli's Theorem Demonstration

The Bernoulli's Theorem Demonstration unit, "FME03", designed by EDIBON is mainly composed of a circular section pipe with the shape of a truncated cone, transparent and with seven pressure taps that allows to measure, simultaneously, the static...

FME04

Available

8.1.4.- HYDRODYNAMICS

FME04

Orifice Discharge

The Orifice Discharge Unit, "FME04", designed by EDIBON allows the study of the different concentration, discharge and velocity coefficients for thin and/or thick wall for different types: colloidal, Venturi or diaphragm.The unit consists of a...

FME05

Available

8.1.8.- HYDRAULIC PIPING SYSTEM

FME05

Energy Losses in Bends

The Energy Losses in Bends unit, "FME05", designed by EDIBON allows to measure and compare the head losses produced by different singular elements: bends, section changes and valves, as well as to study the influence of the flow rate on the value...

FME06

Available

8.1.5.- FLOW VISUALIZATION

FME06

Osborne Reynolds' Demonstration

The Osborne Reynolds Demonstration Unit, "FME06", designed by EDIBON, consists of a cylindrical tank endowed with a nozzle, that is fitted to a methacrylate pipe, which allows the fluid visualization.A spillway guarantees the homogeneity of the...

FME07

Available

8.1.8.- HYDRAULIC PIPING SYSTEM

FME07

Energy Losses in Pipes

With the Energy Losses in Pipes, "FME07", designed by EDIBON, the user will be able to measure the head losses generated in a pipeline for different flow rates in both laminar and turbulent regimes.The unit consists of the following elements, used...

FME08

Available

8.1.3.- HYDROSTATICS

FME08

Hydrostatic Pressure

The Surface Pressure Unit, "FME08", designed by EDIBON, allows to study the center of pressures with a partially or totally submerged quadrant.This unit consists of a quadrant mounted on the arm of a balance that pivots around an axis.When the...

FME09

Available

8.1.5.- FLOW VISUALIZATION

FME09

Flow Visualization in Channels

The Flow Visualization in Channels unit, "FME09", designed by EDIBON, allows the visualization of liquid spillage phenomena in weirs and the study of objects submerged in a fluid stream (aerodynamics).The unit consists of a transparent...

FME10

Available

8.1.2.- MEASUREMENT

FME10

Dead Weight Calibrator

The Pressure Gauge Calibrator, "FME10", designed by EDIBON, allows the study of the operation of a Bourdon type pressure gauge using a standard set of calibrated weights and the determination and the study of the pressure gauge hysteresis...

METACENTRIC HEIGHT DEMONSTRATION - FME11

FME11

Available

8.1.3.- HYDROSTATICS

FME11

Metacentric Height Demonstration

The Metacentric Height Demonstration Unit, "FME11", designed by EDIBON, allows the study of the stability of a floating object by calculating its metacentric height.The unit consists of a floating methacrylate prismatic base, on which a vertical...

FME12

Available

8.1.6.- HYDRAULIC MACHINES: PUMPS

FME12

Series/Parallel Pumps

The Series/Parallel Pumps unit, "FME12", designed by EDIBON, allows the study of the coupling between two series/parallel centrifugal pumps, obtaining the characteristic curves as well as the calculation of the water flow rate.The unit consists of...

CENTRIFUGAL PUMP CHARACTERISTICS - FME13

FME13

Available

8.1.6.- HYDRAULIC MACHINES: PUMPS

FME13

Centrifugal Pump Characteristics

The Centrifugal Pump Characteristics, "FME13", designed by EDIBON, allows the study of several centrifugal pump characteristics such as efficiency, series/parallel couplings, etc.The unit has a centrifugal pump with similar characteristics to the...

FME14

Available

8.1.4.- HYDRODYNAMICS

FME14

Free and Forced Vortex

The Forced and Free Vortex unit, "FME14", designed by EDIBON, allows the study of the fluid rotation in relation to an axis and the study of circular flow at changing velocities.The unit has a cylindrical and transparent deposit with two inlet...

FME15

Available

8.1.8.- HYDRAULIC PIPING SYSTEM

FME15

Water Hammer

With the Water Hammer unit, "FME15", designed by EDIBON, we can demonstrate the effects of the instantaneous or gradual variation of the velocity of a fluid.The water hammer phenomenon, which appears as a consequence of a rapid change in the...

FME16

Available

8.1.7.- HYDRAULIC MACHINES: TURBINES

FME16

Pelton Turbine

The Pelton Turbine unit, "FME16", designed by EDIBON, allows the study of the characteristics of the tangential wheels or pressure turbines commonly used to produce electricity in hydroelectric plants to exploit large hydraulic jumps of low...

FME17

Available

8.1.4.- HYDRODYNAMICS

FME17

Orifice and Free Jet Flow

The Orifice and Free Jet Flow unit, "FME17", designed by EDIBON, allows the study of the different discharge and velocity coefficients in permanent or variable regime as well as the calculation of the discharge times.The unit consists of a...

FME18

Available

8.1.2.- MEASUREMENT

FME18

Flow Meter Demonstration

The Flow Meter Demonstration, "FME18", designed by EDIBON, allows through 3 different flow measurement accessories: Venturi tube, orifice plate and a variable area meter installed in series in the unit, the study to find the flow rate of the fluid...

CAVITATION PHENOMENON DEMONSTRATION - FME19

FME19

Available

8.1.4.- HYDRODYNAMICS

FME19

Cavitation Phenomenon Demonstration

The Cavitation Phenomenon Demonstration unit, "FME19", designed by EDIBON is composed of a Venturi tube with a rectangular cross section, one of its sides being transparent, allowing a better visualization of the cavitation phenomenon.It includes...

FME20

Available

8.1.5.- FLOW VISUALIZATION

FME20

Laminar Flow Demonstration

The Laminar Flow Demostration unit, "FME20", designed by EDIBON, allows a complete study of the bi-dimensional problems associated with laminar flow. Thanks to an efficient system of dye injection we can observe the different models of flow. It...

FME21

Available

8.1.7.- HYDRAULIC MACHINES: TURBINES

FME21

Radial Flow Turbine

The Radial Flow Turbine unit, "FME21", designed by EDIBON, allows the study of a turbomachine, specifically radial turbines capable of handling slower flow levels than other turbine models.This unit consist of a miniature Radial Turbine with two...

VENTURI, BERNOULLI AND CAVITATION UNIT - FME22

FME22

Available

8.1.4.- HYDRODYNAMICS

FME22

Venturi, Bernoulli and Cavitation Unit

The Venturi, Bernoulli and Cavitation unit, "FME22", has been designed by EDIBON to demonstrate some of the practical possibilities that can be achieved with a Venturi tube.This unit is designed for demonstrating some practical possibilities with...

FME23

Available

8.1.8.- HYDRAULIC PIPING SYSTEM

FME23

Basic Pipe Network Unit

The Basic Pipe Network Unit, "FME23", designed by EDIBON, allows the study of pressures and flows created by interconnected pipes, i.e. in a network.The objective of this unit is to simulate the problems that could originate in pipe networks, with...

UNIT FOR THE STUDY OF POROUS BEDS IN VENTURI TUBES (DARCY´S EQUATION) - FME24

FME24

Available

8.1.8.- HYDRAULIC PIPING SYSTEM

FME24

Unit for the Study of Porous Beds in Venturi Tubes (Darcy´s Equation)

The Unit for the Study of Porous Beds in Venturi Tubes (Darcy´s Equation), "FME24", designed by EDIBON, for the study of porous beds in Venturi tubes (Darcy's Equation), allowing the complete and detailed understanding of this equation.The unit is...

FME25

Available

8.1.5.- FLOW VISUALIZATION

FME25

Flow channel, length: 1 m

The Flow Channel, length: 1 m, "FME25", designed by EDIBON, allows to study of the water behavior flowing through a channel.It basically consists of a channel of rectangular cross section with transparent walls, through which water flows.It has a...

DEPRESSION MEASUREMENT SYSTEM (VACUUM GAUGE) - FME26

FME26

Available

8.1.2.- MEASUREMENT

FME26

Depression Measurement System (vacuum gauge)

The Depression Measurement System (vacuum gauge), "FME 26", is designed to be connected to the inlet of some flow aspiration system, in a way that we could measure the depression made by the so-called aspiration system. Such system will be...

FME27

Available

8.1.7.- HYDRAULIC MACHINES: TURBINES

FME27

Axial Flow Turbine

With the Axial Turbine, "FME27", designed by EDIBON, it is possible to study and to understand the axial flow turbines which, unlike the radial flow turbines, the working fluid is parallel to the axis of rotation.This unit consists of an axial...

FME28

Available

8.1.7.- HYDRAULIC MACHINES: TURBINES

FME28

Francis Turbine

With the Francis Turbine unit, "FME28", designed by EDIBON, we study the Francis turbines commonly used when we have average flow rates and heights.This unit consists on a miniature Francis turbine. The water inlet flow is controlled by a valve...

FME29

Available

8.1.7.- HYDRAULIC MACHINES: TURBINES

FME29

Kaplan Turbine

With the Kaplan Turbine unit, "FME29", designed by EDIBON, we study the Kaplan turbines commonly used when we have high flow rates but low flow height.This unit consists on a miniature Kaplan turbine. The water inlet flow is controlled by a valve...

FME30

Available

8.1.2.- MEASUREMENT

FME30

Transparent Vortex Flow Meter

The Transparent Vortex Flow Meter, "FME30", designed by EDIBON allows to perform studies and experiments of different volumetric and mass flow measurement methods, as well as the comparison of continuous and discontinuous methods.This unit...

HORIZONTAL OSBORNE REYNOLDS DEMONSTRATION - FME31

FME31

Available

8.1.5.- FLOW VISUALIZATION

FME31

Horizontal Osborne Reynolds Demonstration

The Osborne Reynolds Horizontal Demonstration Unit, "FME31", designed by EDIBON, allows to study the characteristics of a liquid flowing through a pipe and the Reynolds number in each of the liquid states.The FME31 unit makes it possible to study...

FME32

Available

8.1.2.- MEASUREMENT

FME32

Static Pitot Tube

The Static Pitot Tube, "FME32", designed by EDIBON, the change in flow speed within a tube can be determined.The Pitot static tube can be moved across the whole cross-section of the tube, and thus to measure the pressure profile.This tube is...

PASCAL'S PRINCIPLE DEMONSTRATION - FME33

FME33

Available

8.1.3.- HYDROSTATICS

FME33

Pascal's Principle Demonstration

The Pascal's Principle Demonstration Unit, "FME33", designed by EDIBON, allows to demonstrate Pascal's principle, i.e. that the pressure in an incompressible fluid is independent of the column size section but depends only on its height (liquid...

FME34

Available

8.1.2.- MEASUREMENT

FME34

Fluid Statics and Manometry

The Fluid Statics and Manometry, "FME34", designed by EDIBON, allows the study of static fluids and manometry providing the user with an introduction in the behavior of liquids under hydrostatic conditions (fluids at standstill) and the...

FME35

Available

8.1.3.- HYDROSTATICS

FME35

Fluid Properties

The Fluid Properties Unit, "FME35", designed by EDIBON, allows the study of the fluids fundamental properties that affect their behavior in practical applications.We can study capillarity, density and relative density (specific gravity), buoyancy...

COMPUTER CONTROLLED CENTRIFUGAL COMPRESSOR DEMONSTRATION UNIT - HCCC

HCCC

Available

8.7.5.- COMPRESSORS

HCCC

Computer Controlled Centrifugal Compressor Demonstration Unit

The Computer Controlled Centrifugal Compressor Demonstration Unit, "HCCC", allows the students to measure the operation characteristics of a multistage centrifugal compressor. For that purpose, the unit carries out the actual measurements of the...

COMPUTER CONTROLLED TWO-STAGE COMPRESSOR TEST UNIT - HCDEC

HCDEC

Available

8.7.5.- COMPRESSORS

HCDEC

Computer Controlled Two-Stage Compressor Test Unit

The Computer Controlled Two-Stage Compressor Test Unit, "HCDEC", works with compressed air and presents as a principal device a compression bench with two pistons, low and high pressure.This unit presents four circuits or work dispositions which...

PRECISION PRESSURE GAUGE CALIBRATOR - HCMP

HCMP

Available

8.2.- MEASUREMENT

HCMP

Precision Pressure Gauge Calibrator

The Precision Pressure Gauge Calibrator, "HCMP", is a self-contained and portable dead weight precision pressure gauge calibrator.The unit allows the calibration of pressure gauges up to 300 bar. Calibration is accurate within ± 0.015 % of...

COMPUTER CONTROLLED RECIPROCATING COMPRESSOR UNIT - HCRC

HCRC

Available

8.7.5.- COMPRESSORS

HCRC

Computer Controlled Reciprocating Compressor Unit

The Computer Controlled Reciprocating Compressor Unit, "HCRC", allows students to study and test a fluid power machine and to discover how the compressor flow rate relates to the pressure delivered by the compressor. The unit provides a detailed...

HECA

Available

8.8.- FLUID PIPING SYSTEM

HECA

Air Flow Studies Unit

The Air Flow Studies Unit, "HECA", is a floor standing unit that allows to measure different characteristics of air distribution systems and to demonstrate certain basic principles of fluid mechanics in ducts and jets.The unit is mounted on a...

HEMP

Available

8.2.- MEASUREMENT

HEMP

Pressure Measurement Unit

The Pressure Measurement Unit, "HEMP", enables a wide range of investigations and studies into pressure measurement techniques, using Bourdon type manometers and different U-tube manometers, to understand the operation, the characteristics of the...

COMPUTER CONTROLLED FLOW OF COMPRESSIBLE FLUIDS UNIT - HFCC

HFCC

Available

8.7.5.- COMPRESSORS

HFCC

Computer Controlled Flow of Compressible Fluids Unit

The Computer Controlled Flow of Compressible Fluids Unit, "HFCC", allows to study the variation of pressure and density, the speeds of the fluid, the different fluctuations that the fluid presents when fluids across different sections in a pipe,...

COMPUTER CONTROLLED AXIAL FLOW TURBOMACHINES UNIT - HMFAC

HMFAC

Available

8.7.3.- TURBINES

HMFAC

Computer Controlled Axial Flow Turbomachines Unit

The Computer Controlled Axial Flow Turbomachines Unit, "HMFAC", allows the study of single-stage axial turbomachines, with interchangeable vanes for the study of both a pump and a turbine.The main part of the unit is the axial turbomachine...

COMPUTER CONTROLLED EXPERIMENTAL IMPULSE TURBINE - HTIC

HTIC

Available

5.3.6.- HYDRAULIC ENERGY

HTIC

Computer Controlled Experimental Impulse Turbine

The Computer Controlled Experimental Impulse Turbine, "HTIC", allows to study the characteristics and the behavior of a small scale impulse turbine.This unit includes suitable instrumentation to measure the main parameters:There is a pressure...

COMPUTER CONTROLLED EXPERIMENTAL REACTION TURBINE - HTRC

HTRC

Available

5.3.6.- HYDRAULIC ENERGY

HTRC

Computer Controlled Experimental Reaction Turbine

The Experimental Reaction Turbine, Computer Controlled (PC), "HTRC", allows to study the characteristics of operation of a small scale reaction turbine.This unit includes suitable instrumentation to measure the main parameters:There is a pressure...

COMPUTER CONTROLLED AXIAL FAN TEACHING UNIT - HVAC

HVAC

Available

8.7.2.- FANS

HVAC

Computer Controlled Axial Fan Teaching Unit

The Computer Controlled Axial Fan Teaching Unit, "HVAC", allows the observation, the study and the working process analysis of an axial-flow fan.The main element of this unit is a computer controlled speed centrifugal fan, which is measured...

DROP BALL VISCOMETER AND RESISTANCE COEFFICIENT DETERMINATION UNIT - HVB

HVB

Available

8.2.- MEASUREMENT

HVB

Drop Ball Viscometer and Resistance Coefficient Determination Unit

The Drop Ball Viscometer and Resistance Coefficient Determination Unit, "HVB", designed by EDIBON, consists of two precision transparent tubes fixed onto a frame in which a ball is allowed to drop down through different liquids. Both tubes can be...

COMPUTER CONTROLLED CENTRIFUGAL FAN TEACHING UNIT - HVCC

HVCC

Available

8.7.2.- FANS

HVCC

Computer Controlled Centrifugal Fan Teaching Unit

The Computer Controlled Centrifugal Fan Teaching Unit, "HVCC", allows the students to study the operation characteristics of a centrifugal fan. For that purpose, the unit carries out the measurements of flow, speed, temperature, pressure and...

MOBILE BED AND FLOW VISUALIZATION UNIT (WORKING SECTION: 4000X610 MM) - HVFLM-4

HVFLM-4

Available

13.1.- HYDROLOGY AND HYDROGEOLOGY

HVFLM-4

Mobile Bed and Flow Visualization Unit (working section: 4000x610 mm)

The Mobile Bed and Flow Visualization Unit (working section: 4000 x 610 mm), "HVFLM-4", may be used mainly in two study fields. The first one is the investigation of mobile beds, which are related to water courses and civil engineering structures....

LAMINAR FLOW VISUALIZATION AND ANALYSIS UNIT - LFA

LFA

Available

8.4.- FLOW VISUALIZATION

LFA

Laminar Flow Visualization and Analysis Unit

The Laminar Flow Visualization and Analysis Unit, "LFA", allows a complete study of the two-dimensional problems associated with the laminar flow by the visualization of the different models of flow, which can be observed thanks to an efficient...

BASIC FLUIDS MECHANICS INTEGRATED LABORATORY - LIFLUBA

LIFLUBA

Available

8.1.7.- HYDRAULIC MACHINES: TURBINES

LIFLUBA

Basic Fluids Mechanics Integrated Laboratory

Hydraulics is the branch of science that deals with the mechanical properties of fluids, and Fluid Mechanics provides the foundation for hydraulics.With LIFLUBA (Basic Fluids Mechanics Integrated Laboratory), EDIBON tries to give answer to the...

COMPUTER CONTROLLED MULTIPUMP TESTING BENCH (2 TYPES OF PUMPS) - PB2C

PB2C

Available

8.7.1.- PUMPS

PB2C

Computer Controlled Multipump Testing Bench (2 types of pumps)

The Computer Controlled Multipump Testing Bench (2 types of pumps), "PB2C", allows the students to study the operating characteristics of the centrifugal and gear pumps. This unit allows to control and to measure the most representative parameters...

COMPUTER CONTROLLED AXIAL PUMP BENCH - PBAC

PBAC

Available

8.7.1.- PUMPS

PBAC

Computer Controlled Axial Pump Bench

The Computer Controlled Axial Pump Bench, "PBAC", has been designed by EDIBON to study this type of pumps. It is a bench-top unit that consists of a computer controlled axial pump, a water tank and circulation pipes with a flow regulation valve....

PBCC

Available

8.7.1.- PUMPS

PBCC

Computer Controlled Centrifugal Pump Bench

The Computer Controlled Centrifugal Pump Bench, "PBCC", is a bench-top unit consists of a centrifugal pump computer controlled, a feed water tank, circulation pipes, regulation valves, as well as the enough control elements for the pump...

COMPUTER CONTROLLED GEAR PUMP BENCH - PBEC

PBEC

Available

8.7.1.- PUMPS

PBEC

Computer Controlled Gear Pump Bench

The Computer Controlled Gear Pump Bench, "PBEC", is a bench-top unit consists of a gear pump computer controlled, a feed water tank, circulation pipes, regulation valves, as well as the enough control elements for the pump experiments: two...

COMPUTER CONTROLLED MULTIPUMP TESTING BENCH (4 TYPES OF PUMPS) - PBOC

PBOC

Available

8.7.1.- PUMPS

PBOC

Computer Controlled Multipump Testing Bench (4 types of pumps)

The Computer Controlled Multipump Testing Bench (4 types of pumps), "PBOC", allows the students to study the operating characteristics of several types of pumps. This unit allows to control and to measure the most representative parameters of the...

COMPUTER CONTROLLED PISTON PUMP BENCH - PBRC

PBRC

Available

8.7.1.- PUMPS

PBRC

Computer Controlled Piston Pump Bench

The Computer Controlled Piston Pump Bench, "PBRC", is a bench-top unit that consists of a piston pump, a feed tank, flow meter tank calibrated for taking flow measurements, circulation pipes, manual valves and a solenoid valve, computer...

COMPUTER CONTROLLED SERIES/PARALLEL PUMPS BENCH - PBSPC

PBSPC

Available

8.7.1.- PUMPS

PBSPC

Computer Controlled Series/Parallel Pumps Bench

The Computer Controlled Series/Parallel Pumps Bench, "PBSPC", is designed to demonstrate the operational advantages of parallel or series operation, depending on the required duty.This unit consists of two centrifugal pumps, a feed water tank,...

COMPUTER CONTROLLED AERODYNAMIC TUNNEL, 1200X1200 MM - TA1200/1200C

TA1200/1200C

Available

8.6.- AERODYNAMICS

TA1200/1200C

Computer Controlled Aerodynamic Tunnel, 1200X1200 mm

Aerodynamics is the part of fluid mechanics that studies the motion of gases and the forces or reactions to which the bodies they interact with are subjected. Aerodynamics is not only important by itself but also as a complement to aeronautics....

COMPUTER CONTROLLED AXIAL FLOW TURBINE - TFAC

TFAC

Available

5.3.6.- HYDRAULIC ENERGY

TFAC

Computer Controlled Axial Flow Turbine

The Computer Controlled Axial Flow Turbine, "TFAC", consists of a small-scale turbine with single-stage axial flow input. It has eight nozzles that act as water rings to the rotor, four of which have an incidence angle of 20º and the other four of...

COMPUTER CONTROLLED FRANCIS TURBINE - TFC

TFC

Available

5.3.6.- HYDRAULIC ENERGY

TFC

Computer Controlled Francis Turbine

The Computer Controlled Francis Turbine, "TFC", consists of a small-scale Francis Turbine, with a valve that allows flow regulation and has a ring with adjustable guide vanes that allows control of the angle of incidence of the water in the...

COMPUTER CONTROLLED RADIAL FLOW TURBINE - TFRC

TFRC

Available

5.3.6.- HYDRAULIC ENERGY

TFRC

Computer Controlled Radial Flow Turbine

The Computer Controlled Radial Flow Turbine, "TFRC", consists of a small-scale radial flow turbine with two nozzles at 90 degrees to the perpendicular direction of the axis of rotation.In order to raise the fluid, it has a computer controlled pump...

TKC

Available

5.3.6.- HYDRAULIC ENERGY

TKC

Computer Controlled Kaplan Turbine

The Computer Controlled Kaplan Turbine, "TKC", consists of a small-scale Kaplan turbine that has a ring with adjustable guide vanes, which allow the control of water flow in the turbine.In order to raise the fluid, it has a computer controlled...

TMCP

Available

8.2.- MEASUREMENT

TMCP

Pressure Measurement and Calibration Unit

The Pressure Measurement and Calibration Unit, "TMCP", has been designed to study the concept of pressure and the different methods and techniques used to measure this variable.The dead-weight calibrator consists of a cylinder in which interior a...

TPC

Available

5.3.6.- HYDRAULIC ENERGY

TPC

Computer Controlled Pelton Turbine

The Computer Controlled Pelton Turbine, "TPC", designed by EDIBON, consists of a small-scale Pelton turbine, with a valve that allows the flow to be regulated. The turbine includes a PELTON runner with 16 buckets, which can be clearly seen through...

UVF

Available

8.4.- FLOW VISUALIZATION

UVF

Hydrogen Bubble Flow Visualization Unit

The Hydrogen Bubble Flow Visualization Unit, "UVF", is a self-contained unit designed to study different flow patterns through the hydrogen bubble flow visualization technique.Bubbles are generated by electrolysis by the application of an electric...

AFTC

Available

8.8.- FLUID PIPING SYSTEM

AFTC

Computer Controlled Fluid Friction in Pipes, with Hydraulics Bench (FME00)

The Computer Controlled Fluid Friction in Pipes, with Hydraulics Bench (FME00), "AFTC", is designed to determine the friction coefficient in pipes of several diameters and roughness, to study the pressure losses and pressure development in...

AMTC

Available

8.8.- FLUID PIPING SYSTEM

AMTC

Computer Controlled Pipe Network Unit, with Hydraulics Bench (FME00)

The Computer Controlled Pipe Network Unit, with Hydraulics Bench (FME00), "AMTC", consists of a pipe network, a lateral panel where all the elements to test are located and a hydraulics bench, which has all the elements and accessories required...

BDAS

Available

8.1.7.- HYDRAULIC MACHINES: TURBINES

BDAS

Data Acquisition System and Sensors

BDAS is designed to monitor the measurements of each unit type "FME" from a computer (PC).This system can monitor any unit, checking the revolutions given by the water pump or the torque, differential pressures for Bernoulli theorems, pressure...

BHI

Available

8.3.- HYDROSTATICS

BHI

Hydrostatics Bench & Fluid Properties

The Hydrostatics Bench and Fluid Properties, "BHI", is a compact, mobile and independent unit.There is a water storage tank, to work in a closed system, at the bottom of the bench. The water is distributed by hand pumps from this tank to two upper...

CAS

Available

13.1.- HYDROLOGY AND HYDROGEOLOGY

CAS

Sediment Transport Demonstration Channel

The Sediment Transport Demonstration Channel, "CAS", designed by EDIBON, consist of an inclinable channel mounted on a base plate, supported by two supports, with a discharge tank and recirculating pump. This tank is in the Basic Hydraulic Feed...

EGAC

Available

8.8.- FLUID PIPING SYSTEM

EGAC

Computer Controlled Water Hammer Unit

The Computer Controlled Water Hammer Unit, "EGAC", is designed to demonstrate the effects of an instantaneous variation of the speed of a fluid. It is possible to study the water hammer, which is the consequence of a quick change in a fluid speed....

FME00

Available

8.1.1.- BASE UNITS

FME00

Hydraulics Bench

The Hydraulics Bench, "FME00", designed by EDIBON, allows the study of fluid behaviour, hydraulic theory and the properties of fluid mechanics.It is formed by a movable hydraulics bench used to hold a wide variety of modules, which allow the...

FME00/B

Available

8.1.1.- BASE UNITS

FME00/B

Basic Hydraulic Feed System

The Basic Hydraulic Feed System, "FME00/B", designed by EDIBON is a service unit for different Fluid Mechanics Units as: "FME" type modules, Fluid Friction in Pipes Unit "AFT", etc., increasing the equipment profitability.

FME01

Available

8.1.4.- HYDRODYNAMICS

FME01

Jet Impact on Surfaces

The Jet Impact on Surfaces Unit, "FME01", designed by EDIBON, allows the study of the interaction between a moving fluid jet and different impact surfaces, providing a detailed understanding of fluid dynamics principles and their application in...

FME02

Available

8.1.2.- MEASUREMENT

FME02

Flow over Weirs

The Flow over Weirs, "FME02", designed by EDIBON, has many elements that are used in combination with the Hydraulics Bench (FME00): A special mouthpiece is coupled to the outlet mouthpiece for water in the Hydraulics Bench (FME00).Two soothing...

FME03

Available

8.1.4.- HYDRODYNAMICS

FME03

Bernoulli's Theorem Demonstration

The Bernoulli's Theorem Demonstration unit, "FME03", designed by EDIBON is mainly composed of a circular section pipe with the shape of a truncated cone, transparent and with seven pressure taps that allows to measure, simultaneously, the static...

FME04

Available

8.1.4.- HYDRODYNAMICS

FME04

Orifice Discharge

The Orifice Discharge Unit, "FME04", designed by EDIBON allows the study of the different concentration, discharge and velocity coefficients for thin and/or thick wall for different types: colloidal, Venturi or diaphragm.The unit consists of a...

FME05

Available

8.1.8.- HYDRAULIC PIPING SYSTEM

FME05

Energy Losses in Bends

The Energy Losses in Bends unit, "FME05", designed by EDIBON allows to measure and compare the head losses produced by different singular elements: bends, section changes and valves, as well as to study the influence of the flow rate on the value...

FME06

Available

8.1.5.- FLOW VISUALIZATION

FME06

Osborne Reynolds' Demonstration

The Osborne Reynolds Demonstration Unit, "FME06", designed by EDIBON, consists of a cylindrical tank endowed with a nozzle, that is fitted to a methacrylate pipe, which allows the fluid visualization.A spillway guarantees the homogeneity of the...

FME07

Available

8.1.8.- HYDRAULIC PIPING SYSTEM

FME07

Energy Losses in Pipes

With the Energy Losses in Pipes, "FME07", designed by EDIBON, the user will be able to measure the head losses generated in a pipeline for different flow rates in both laminar and turbulent regimes.The unit consists of the following elements, used...

FME08

Available

8.1.3.- HYDROSTATICS

FME08

Hydrostatic Pressure

The Surface Pressure Unit, "FME08", designed by EDIBON, allows to study the center of pressures with a partially or totally submerged quadrant.This unit consists of a quadrant mounted on the arm of a balance that pivots around an axis.When the...

FME09

Available

8.1.5.- FLOW VISUALIZATION

FME09

Flow Visualization in Channels

The Flow Visualization in Channels unit, "FME09", designed by EDIBON, allows the visualization of liquid spillage phenomena in weirs and the study of objects submerged in a fluid stream (aerodynamics).The unit consists of a transparent...

FME10

Available

8.1.2.- MEASUREMENT

FME10

Dead Weight Calibrator

The Pressure Gauge Calibrator, "FME10", designed by EDIBON, allows the study of the operation of a Bourdon type pressure gauge using a standard set of calibrated weights and the determination and the study of the pressure gauge hysteresis...

FME11

Available

8.1.3.- HYDROSTATICS

FME11

Metacentric Height Demonstration

The Metacentric Height Demonstration Unit, "FME11", designed by EDIBON, allows the study of the stability of a floating object by calculating its metacentric height.The unit consists of a floating methacrylate prismatic base, on which a vertical...

FME12

Available

8.1.6.- HYDRAULIC MACHINES: PUMPS

FME12

Series/Parallel Pumps

The Series/Parallel Pumps unit, "FME12", designed by EDIBON, allows the study of the coupling between two series/parallel centrifugal pumps, obtaining the characteristic curves as well as the calculation of the water flow rate.The unit consists of...

FME13

Available

8.1.6.- HYDRAULIC MACHINES: PUMPS

FME13

Centrifugal Pump Characteristics

The Centrifugal Pump Characteristics, "FME13", designed by EDIBON, allows the study of several centrifugal pump characteristics such as efficiency, series/parallel couplings, etc.The unit has a centrifugal pump with similar characteristics to the...

FME14

Available

8.1.4.- HYDRODYNAMICS

FME14

Free and Forced Vortex

The Forced and Free Vortex unit, "FME14", designed by EDIBON, allows the study of the fluid rotation in relation to an axis and the study of circular flow at changing velocities.The unit has a cylindrical and transparent deposit with two inlet...

FME15

Available

8.1.8.- HYDRAULIC PIPING SYSTEM

FME15

Water Hammer

With the Water Hammer unit, "FME15", designed by EDIBON, we can demonstrate the effects of the instantaneous or gradual variation of the velocity of a fluid.The water hammer phenomenon, which appears as a consequence of a rapid change in the...

FME16

Available

8.1.7.- HYDRAULIC MACHINES: TURBINES

FME16

Pelton Turbine

The Pelton Turbine unit, "FME16", designed by EDIBON, allows the study of the characteristics of the tangential wheels or pressure turbines commonly used to produce electricity in hydroelectric plants to exploit large hydraulic jumps of low...

FME17

Available

8.1.4.- HYDRODYNAMICS

FME17

Orifice and Free Jet Flow

The Orifice and Free Jet Flow unit, "FME17", designed by EDIBON, allows the study of the different discharge and velocity coefficients in permanent or variable regime as well as the calculation of the discharge times.The unit consists of a...

FME18

Available

8.1.2.- MEASUREMENT

FME18

Flow Meter Demonstration

The Flow Meter Demonstration, "FME18", designed by EDIBON, allows through 3 different flow measurement accessories: Venturi tube, orifice plate and a variable area meter installed in series in the unit, the study to find the flow rate of the fluid...

FME19

Available

8.1.4.- HYDRODYNAMICS

FME19

Cavitation Phenomenon Demonstration

The Cavitation Phenomenon Demonstration unit, "FME19", designed by EDIBON is composed of a Venturi tube with a rectangular cross section, one of its sides being transparent, allowing a better visualization of the cavitation phenomenon.It includes...

FME20

Available

8.1.5.- FLOW VISUALIZATION

FME20

Laminar Flow Demonstration

The Laminar Flow Demostration unit, "FME20", designed by EDIBON, allows a complete study of the bi-dimensional problems associated with laminar flow. Thanks to an efficient system of dye injection we can observe the different models of flow. It...

FME21

Available

8.1.7.- HYDRAULIC MACHINES: TURBINES

FME21

Radial Flow Turbine

The Radial Flow Turbine unit, "FME21", designed by EDIBON, allows the study of a turbomachine, specifically radial turbines capable of handling slower flow levels than other turbine models.This unit consist of a miniature Radial Turbine with two...

FME22

Available

8.1.4.- HYDRODYNAMICS

FME22

Venturi, Bernoulli and Cavitation Unit

The Venturi, Bernoulli and Cavitation unit, "FME22", has been designed by EDIBON to demonstrate some of the practical possibilities that can be achieved with a Venturi tube.This unit is designed for demonstrating some practical possibilities with...

FME23

Available

8.1.8.- HYDRAULIC PIPING SYSTEM

FME23

Basic Pipe Network Unit

The Basic Pipe Network Unit, "FME23", designed by EDIBON, allows the study of pressures and flows created by interconnected pipes, i.e. in a network.The objective of this unit is to simulate the problems that could originate in pipe networks, with...

FME24

Available

8.1.8.- HYDRAULIC PIPING SYSTEM

FME24

Unit for the Study of Porous Beds in Venturi Tubes (Darcy´s Equation)

The Unit for the Study of Porous Beds in Venturi Tubes (Darcy´s Equation), "FME24", designed by EDIBON, for the study of porous beds in Venturi tubes (Darcy's Equation), allowing the complete and detailed understanding of this equation.The unit is...

FME25

Available

8.1.5.- FLOW VISUALIZATION

FME25

Flow channel, length: 1 m

The Flow Channel, length: 1 m, "FME25", designed by EDIBON, allows to study of the water behavior flowing through a channel.It basically consists of a channel of rectangular cross section with transparent walls, through which water flows.It has a...

FME26

Available

8.1.2.- MEASUREMENT

FME26

Depression Measurement System (vacuum gauge)

The Depression Measurement System (vacuum gauge), "FME 26", is designed to be connected to the inlet of some flow aspiration system, in a way that we could measure the depression made by the so-called aspiration system. Such system will be...

FME27

Available

8.1.7.- HYDRAULIC MACHINES: TURBINES

FME27

Axial Flow Turbine

With the Axial Turbine, "FME27", designed by EDIBON, it is possible to study and to understand the axial flow turbines which, unlike the radial flow turbines, the working fluid is parallel to the axis of rotation.This unit consists of an axial...

FME28

Available

8.1.7.- HYDRAULIC MACHINES: TURBINES

FME28

Francis Turbine

With the Francis Turbine unit, "FME28", designed by EDIBON, we study the Francis turbines commonly used when we have average flow rates and heights.This unit consists on a miniature Francis turbine. The water inlet flow is controlled by a valve...

FME29

Available

8.1.7.- HYDRAULIC MACHINES: TURBINES

FME29

Kaplan Turbine

With the Kaplan Turbine unit, "FME29", designed by EDIBON, we study the Kaplan turbines commonly used when we have high flow rates but low flow height.This unit consists on a miniature Kaplan turbine. The water inlet flow is controlled by a valve...

FME30

Available

8.1.2.- MEASUREMENT

FME30

Transparent Vortex Flow Meter

The Transparent Vortex Flow Meter, "FME30", designed by EDIBON allows to perform studies and experiments of different volumetric and mass flow measurement methods, as well as the comparison of continuous and discontinuous methods.This unit...

FME31

Available

8.1.5.- FLOW VISUALIZATION

FME31

Horizontal Osborne Reynolds Demonstration

The Osborne Reynolds Horizontal Demonstration Unit, "FME31", designed by EDIBON, allows to study the characteristics of a liquid flowing through a pipe and the Reynolds number in each of the liquid states.The FME31 unit makes it possible to study...

FME32

Available

8.1.2.- MEASUREMENT

FME32

Static Pitot Tube

The Static Pitot Tube, "FME32", designed by EDIBON, the change in flow speed within a tube can be determined.The Pitot static tube can be moved across the whole cross-section of the tube, and thus to measure the pressure profile.This tube is...

FME33

Available

8.1.3.- HYDROSTATICS

FME33

Pascal's Principle Demonstration

The Pascal's Principle Demonstration Unit, "FME33", designed by EDIBON, allows to demonstrate Pascal's principle, i.e. that the pressure in an incompressible fluid is independent of the column size section but depends only on its height (liquid...

FME34

Available

8.1.2.- MEASUREMENT

FME34

Fluid Statics and Manometry

The Fluid Statics and Manometry, "FME34", designed by EDIBON, allows the study of static fluids and manometry providing the user with an introduction in the behavior of liquids under hydrostatic conditions (fluids at standstill) and the...

FME35

Available

8.1.3.- HYDROSTATICS

FME35

Fluid Properties

The Fluid Properties Unit, "FME35", designed by EDIBON, allows the study of the fluids fundamental properties that affect their behavior in practical applications.We can study capillarity, density and relative density (specific gravity), buoyancy...

HCCC

Available

8.7.5.- COMPRESSORS

HCCC

Computer Controlled Centrifugal Compressor Demonstration Unit

The Computer Controlled Centrifugal Compressor Demonstration Unit, "HCCC", allows the students to measure the operation characteristics of a multistage centrifugal compressor. For that purpose, the unit carries out the actual measurements of the...

HCDEC

Available

8.7.5.- COMPRESSORS

HCDEC

Computer Controlled Two-Stage Compressor Test Unit

The Computer Controlled Two-Stage Compressor Test Unit, "HCDEC", works with compressed air and presents as a principal device a compression bench with two pistons, low and high pressure.This unit presents four circuits or work dispositions which...

HCMP

Available

8.2.- MEASUREMENT

HCMP

Precision Pressure Gauge Calibrator

The Precision Pressure Gauge Calibrator, "HCMP", is a self-contained and portable dead weight precision pressure gauge calibrator.The unit allows the calibration of pressure gauges up to 300 bar. Calibration is accurate within ± 0.015 % of...

HCRC

Available

8.7.5.- COMPRESSORS

HCRC

Computer Controlled Reciprocating Compressor Unit

The Computer Controlled Reciprocating Compressor Unit, "HCRC", allows students to study and test a fluid power machine and to discover how the compressor flow rate relates to the pressure delivered by the compressor. The unit provides a detailed...

HECA

Available

8.8.- FLUID PIPING SYSTEM

HECA

Air Flow Studies Unit

The Air Flow Studies Unit, "HECA", is a floor standing unit that allows to measure different characteristics of air distribution systems and to demonstrate certain basic principles of fluid mechanics in ducts and jets.The unit is mounted on a...

HEMP

Available

8.2.- MEASUREMENT

HEMP

Pressure Measurement Unit

The Pressure Measurement Unit, "HEMP", enables a wide range of investigations and studies into pressure measurement techniques, using Bourdon type manometers and different U-tube manometers, to understand the operation, the characteristics of the...

HFCC

Available

8.7.5.- COMPRESSORS

HFCC

Computer Controlled Flow of Compressible Fluids Unit

The Computer Controlled Flow of Compressible Fluids Unit, "HFCC", allows to study the variation of pressure and density, the speeds of the fluid, the different fluctuations that the fluid presents when fluids across different sections in a pipe,...

HMFAC

Available

8.7.3.- TURBINES

HMFAC

Computer Controlled Axial Flow Turbomachines Unit

The Computer Controlled Axial Flow Turbomachines Unit, "HMFAC", allows the study of single-stage axial turbomachines, with interchangeable vanes for the study of both a pump and a turbine.The main part of the unit is the axial turbomachine...

HTIC

Available

5.3.6.- HYDRAULIC ENERGY

HTIC

Computer Controlled Experimental Impulse Turbine

The Computer Controlled Experimental Impulse Turbine, "HTIC", allows to study the characteristics and the behavior of a small scale impulse turbine.This unit includes suitable instrumentation to measure the main parameters:There is a pressure...

HTRC

Available

5.3.6.- HYDRAULIC ENERGY

HTRC

Computer Controlled Experimental Reaction Turbine

The Experimental Reaction Turbine, Computer Controlled (PC), "HTRC", allows to study the characteristics of operation of a small scale reaction turbine.This unit includes suitable instrumentation to measure the main parameters:There is a pressure...

HVAC

Available

8.7.2.- FANS

HVAC

Computer Controlled Axial Fan Teaching Unit

The Computer Controlled Axial Fan Teaching Unit, "HVAC", allows the observation, the study and the working process analysis of an axial-flow fan.The main element of this unit is a computer controlled speed centrifugal fan, which is measured...

HVB

Available

8.2.- MEASUREMENT

HVB

Drop Ball Viscometer and Resistance Coefficient Determination Unit

The Drop Ball Viscometer and Resistance Coefficient Determination Unit, "HVB", designed by EDIBON, consists of two precision transparent tubes fixed onto a frame in which a ball is allowed to drop down through different liquids. Both tubes can be...

HVCC

Available

8.7.2.- FANS

HVCC

Computer Controlled Centrifugal Fan Teaching Unit

The Computer Controlled Centrifugal Fan Teaching Unit, "HVCC", allows the students to study the operation characteristics of a centrifugal fan. For that purpose, the unit carries out the measurements of flow, speed, temperature, pressure and...

HVFLM-4

Available

13.1.- HYDROLOGY AND HYDROGEOLOGY

HVFLM-4

Mobile Bed and Flow Visualization Unit (working section: 4000x610 mm)

The Mobile Bed and Flow Visualization Unit (working section: 4000 x 610 mm), "HVFLM-4", may be used mainly in two study fields. The first one is the investigation of mobile beds, which are related to water courses and civil engineering structures....

LFA

Available

8.4.- FLOW VISUALIZATION

LFA

Laminar Flow Visualization and Analysis Unit

The Laminar Flow Visualization and Analysis Unit, "LFA", allows a complete study of the two-dimensional problems associated with the laminar flow by the visualization of the different models of flow, which can be observed thanks to an efficient...

LIFLUBA

Available

8.1.7.- HYDRAULIC MACHINES: TURBINES

LIFLUBA

Basic Fluids Mechanics Integrated Laboratory

Hydraulics is the branch of science that deals with the mechanical properties of fluids, and Fluid Mechanics provides the foundation for hydraulics.With LIFLUBA (Basic Fluids Mechanics Integrated Laboratory), EDIBON tries to give answer to the...

PB2C

Available

8.7.1.- PUMPS

PB2C

Computer Controlled Multipump Testing Bench (2 types of pumps)

The Computer Controlled Multipump Testing Bench (2 types of pumps), "PB2C", allows the students to study the operating characteristics of the centrifugal and gear pumps. This unit allows to control and to measure the most representative parameters...

PBAC

Available

8.7.1.- PUMPS

PBAC

Computer Controlled Axial Pump Bench

The Computer Controlled Axial Pump Bench, "PBAC", has been designed by EDIBON to study this type of pumps. It is a bench-top unit that consists of a computer controlled axial pump, a water tank and circulation pipes with a flow regulation valve....

PBCC

Available

8.7.1.- PUMPS

PBCC

Computer Controlled Centrifugal Pump Bench

The Computer Controlled Centrifugal Pump Bench, "PBCC", is a bench-top unit consists of a centrifugal pump computer controlled, a feed water tank, circulation pipes, regulation valves, as well as the enough control elements for the pump...

PBEC

Available

8.7.1.- PUMPS

PBEC

Computer Controlled Gear Pump Bench

The Computer Controlled Gear Pump Bench, "PBEC", is a bench-top unit consists of a gear pump computer controlled, a feed water tank, circulation pipes, regulation valves, as well as the enough control elements for the pump experiments: two...

PBOC

Available

8.7.1.- PUMPS

PBOC

Computer Controlled Multipump Testing Bench (4 types of pumps)

The Computer Controlled Multipump Testing Bench (4 types of pumps), "PBOC", allows the students to study the operating characteristics of several types of pumps. This unit allows to control and to measure the most representative parameters of the...

PBRC

Available

8.7.1.- PUMPS

PBRC

Computer Controlled Piston Pump Bench

The Computer Controlled Piston Pump Bench, "PBRC", is a bench-top unit that consists of a piston pump, a feed tank, flow meter tank calibrated for taking flow measurements, circulation pipes, manual valves and a solenoid valve, computer...

PBSPC

Available

8.7.1.- PUMPS

PBSPC

Computer Controlled Series/Parallel Pumps Bench

The Computer Controlled Series/Parallel Pumps Bench, "PBSPC", is designed to demonstrate the operational advantages of parallel or series operation, depending on the required duty.This unit consists of two centrifugal pumps, a feed water tank,...

TA1200/1200C

Available

8.6.- AERODYNAMICS

TA1200/1200C

Computer Controlled Aerodynamic Tunnel, 1200X1200 mm

Aerodynamics is the part of fluid mechanics that studies the motion of gases and the forces or reactions to which the bodies they interact with are subjected. Aerodynamics is not only important by itself but also as a complement to aeronautics....

TFAC

Available

5.3.6.- HYDRAULIC ENERGY

TFAC

Computer Controlled Axial Flow Turbine

The Computer Controlled Axial Flow Turbine, "TFAC", consists of a small-scale turbine with single-stage axial flow input. It has eight nozzles that act as water rings to the rotor, four of which have an incidence angle of 20º and the other four of...

TFC

Available

5.3.6.- HYDRAULIC ENERGY

TFC

Computer Controlled Francis Turbine

The Computer Controlled Francis Turbine, "TFC", consists of a small-scale Francis Turbine, with a valve that allows flow regulation and has a ring with adjustable guide vanes that allows control of the angle of incidence of the water in the...

TFRC

Available

5.3.6.- HYDRAULIC ENERGY

TFRC

Computer Controlled Radial Flow Turbine

The Computer Controlled Radial Flow Turbine, "TFRC", consists of a small-scale radial flow turbine with two nozzles at 90 degrees to the perpendicular direction of the axis of rotation.In order to raise the fluid, it has a computer controlled pump...

TKC

Available

5.3.6.- HYDRAULIC ENERGY

TKC

Computer Controlled Kaplan Turbine

The Computer Controlled Kaplan Turbine, "TKC", consists of a small-scale Kaplan turbine that has a ring with adjustable guide vanes, which allow the control of water flow in the turbine.In order to raise the fluid, it has a computer controlled...

TMCP

Available

8.2.- MEASUREMENT

TMCP

Pressure Measurement and Calibration Unit

The Pressure Measurement and Calibration Unit, "TMCP", has been designed to study the concept of pressure and the different methods and techniques used to measure this variable.The dead-weight calibrator consists of a cylinder in which interior a...

TPC

Available

5.3.6.- HYDRAULIC ENERGY

TPC

Computer Controlled Pelton Turbine

The Computer Controlled Pelton Turbine, "TPC", designed by EDIBON, consists of a small-scale Pelton turbine, with a valve that allows the flow to be regulated. The turbine includes a PELTON runner with 16 buckets, which can be clearly seen through...

UVF

Available

8.4.- FLOW VISUALIZATION

UVF

Hydrogen Bubble Flow Visualization Unit

The Hydrogen Bubble Flow Visualization Unit, "UVF", is a self-contained unit designed to study different flow patterns through the hydrogen bubble flow visualization technique.Bubbles are generated by electrolysis by the application of an electric...

8TV Technical and Vocational Education Fluid Mechanics Laboratory

Expansions

Modules

RELATED NEWS

SUPPLEMENTARY EQUIPMENT