9.10.- INSTALLATIONS AND MAINTENANCE

The needs of today's society are a challenge for any industry, since they have to be in continuous evolution and renewal to adapt to those needs.

View more

In recent years, as a result of the new industrial revolution or "Industry 4.0", the emergence of the "Industrial Internet of Things" ("IIoT") and the "Smart Factories", that adaptation is possible thanks to the application of the most sophisticated techniques in the design of new facilities or in the renovation of existing ones.

In spite of all these technological advances and the exhaustive controls carried out, it should not be forgotten that any element that take part in the productive process is going to be subjected to a mechanical and electrical wear (efforts, loads, etc.) and its useful life is limited. To avoid catastrophic failures, stoppages in production or any type of process that implies an increase of non-productive times and, therefore, an increase of costs, it is extremely important to carry out a good maintenance of machinery, electrical systems, etc.

Traditionally, only two types of maintenance were considered:

  • Corrective: the fault is solved once it has already occurred.
  • Preventive: periodic review of all those problematic elements and their replacement if required.

These types of maintenance involve very high and unnecessary costs in most cases. Nowadays, thanks to the available technology, it is possible to carry out predictive maintenance consisting of a comprehensive analysis of all those variables that take part in all the components of a system and be able to replace them at the right time.

But, if more control over the failures that can suffer all those mechanical components subject to wear is preferred, there is another type of maintenance, known as proactive maintenance. It goes one step further than the predictive maintenance, looking for the root of the problem.

View Products
Related Materials

INSTALLATIONS AND MAINTENANCE EQUIPMENT

1.- PHYSICS 2.- ELECTRONICS 3.- COMMUNICATIONS 4.- ELECTRICITY 5.- ENERGY 6.- MECHATRONICS & AUTOMATION 7.- MECHANICS 8.- FLUID MECHANICS 9.- THERMODYNAMICS & THERMOTECHNICS 10.- PROCESS CONTROL 11.- CHEMICAL ENGINEERING 12.- FOOD & WATER TECHNOLOGIES 13.- ENVIRONMENT 14.- BIOMEDICAL ENGINEERING LABORATORY ACCESSORIES CUSTOMIZED PILOT PLANTS
9.2.- HEATING, VENTILATION, AIR CONDITIONING AND HOT WATER 9.3.- HEAT PUMPS 9.4.- REFRIGERATION 9.5.- THERMAL HYDRAULIC PIPING SYSTEM 9.6.- HEAT TRANSFER 9.7.- HEAT EXCHANGERS 9.8.- THERMAL MACHINES 9.9.- INTERNAL COMBUSTION ENGINES 9.10.- INSTALLATIONS AND MAINTENANCE 9.1.- FUNDAMENTALS AND BASIC CONCEPTS OF THERMODYNAMICS
9.10.1.- CUTAWAY MODELS 9.10.2.- DETACHABLE MODELS 9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING
Showing 1-30 of 37 item(s)
12 24 36
UNIT TO STUDY A FILTER DRIER CUTAWAY MODEL - DFCM
  • DFCM
Available
9.10.1.- CUTAWAY MODELS

DFCM

Unit to Study a Filter Drier Cutaway Model

The Unit to Study a Filter Drier Cutaway Model, "DFCM", allows the students to visualize the inner parts of a (element), to evaluate the relation with each other accurately and to understand their functionThe cutaway model of a filter drier is...
View Unit
UNIT TO STUDY A GAS METER CUTAWAY MODEL - GMCM
  • GMCM
Available
9.10.1.- CUTAWAY MODELS

GMCM

Unit to Study a Gas Meter Cutaway Model

The Unit to Study a Gas Meter Cutaway Model, "GMCM", allows the students to visualize the inner parts of a gas meter, to evaluate the relation with each other accurately and to understand their function.It is a measurement device to determine the...
View Unit
UNIT TO STUDY A HELICAL OIL SEPARATOR CUTAWAY MODEL - HOSCM
  • HOSCM
Available
9.10.1.- CUTAWAY MODELS

HOSCM

Unit to Study a Helical Oil Separator Cutaway Model

The Unit to Study a Helical Oil Separator Cutaway Model, "HOSCM", allows the students to visualize the inner parts of a liquid separator, to evaluate the relation with each other accurately and to understand their function.It is a real model used...
View Unit
UNIT TO STUDY A LIQUID SEPARATOR CUTAWAY MODEL - LSCM
  • LSCM
Available
9.10.1.- CUTAWAY MODELS

LSCM

Unit to Study a Liquid Separator Cutaway Model

The Unit to Study a Liquid Separator Cutaway Model, "LSCM", designed by EDIBON, allows the students to visualize the inner parts of a liquid separator, to evaluate the relation with each other accurately and to understand their function.The...
View Unit
UNIT TO STUDY AN OPEN REFRIGERANT COMPRESSOR CUTAWAY MODEL - OCCM
  • OCCM
Available
9.10.1.- CUTAWAY MODELS

OCCM

Unit to Study an Open Refrigerant Compressor Cutaway Model

The Unit to Study an Open Refrigerant Compressor Cutaway Model, "HCCM", allows the students to visualize the inner parts of an open compressor, to evaluate the relation with each other accurately and to understand their function.This unit allows...
View Unit
INTRODUCTION TO REFRIGERATION UNIT - TIR
  • TIR
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

TIR

Introduction to Refrigeration Unit

The Introduction to Refrigeration Unit, "TIR", is a unit with exchangeable sets in which the components are mounted on plates and quickly connected by flexible hoses.The unit consists of a frame with a compressor, a refrigerant accumulator tank to...
View Unit
TEMPERATURE MEASUREMENT TRAINING UNIT - TEMT
  • TEMT
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

TEMT

Temperature Measurement Training Unit

The Temperature Measurement Training Unit, "TEMT", allows to compare the response of several devices to measure the temperature for different flows and different installation position of these devices.The unit includes four different measuring...
View Unit
ASSEMBLY AND MAINTENANCE IN REFRIGERATION SYSTEMS UNIT - TAMR
  • TAMR
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

TAMR

Assembly and Maintenance in Refrigeration Systems Unit

The Assembly and Maintenance in Refrigeration Systems Unit, "TAMR", has been designed to teach the students the planning, implementation and checking of processes related to the assembly, startup and maintenance of refrigeration systems.The fully...
View Unit
HOME REFRIGERATION MODEL - TRAMC/1
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

TRAMC/1

Home Refrigeration Model

Accessory of TRAMC
The minimum supply consists of two main elements: the TRAMC Unit Base, "TRAMC-UB", and at least one of the required elements described below.The models are interconnected by special refrigerant hoses.The main components of the TRAMC Unit Base,...
View Unit
SIMPLE AIR CONDITIONING SYSTEM MODEL FOR ROOM COOLING - TRAMC/3
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

TRAMC/3

Simple Air Conditioning System Model for Room Cooling

Accessory of TRAMC
The minimum supply consists of two main elements: the TRAMC Unit Base, "TRAMC-UB", and at least one of the required elements described below. The models are interconnected by special refrigerant hoses.The main components of the TRAMC Unit Base,...
View Unit
COMPLETE AIR CONDITIONING SYSTEM MODEL - TRAMC/4
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

TRAMC/4

Complete Air Conditioning System Model

Accessory of TRAMC
The minimum supply consists of two main elements: the TRAMC Unit Base, "TRAMC-UB", and at least one of the required elements described below.The models are interconnected by special refrigerant hoses.The main components of the TRAMC Unit Base,...
View Unit
MEASUREMENT AND REGULATION STATION UNIT - MRST
  • MRST
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

MRST

Measurement and Regulation Station Unit

The Measurement and Regulation Station Trainer,"MRST", designed by EDIBON is a totally accessible bench-top unit. The unit works with an air compressor that simulates the gas flowing inside the pipes (air testing), allowing to check the tightness...
View Unit
INSTANTANEOUS GAS HEATER EXPERIMENTATION UNIT - IGHT
  • IGHT
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

IGHT

Instantaneous Gas Heater Experimentation Unit

The Instantaneous Gas Heater Trainer, ,IGHT,, designed by EDIBON, is a training unit with wheels to facilitate its mobility that represents a gas heater training system. The unit operates with air, simulating the operation of the heater, so it can...
View Unit
FORCED DRAFT GAS BURNER UNIT - GBT
  • GBT
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

GBT

Forced Draft Gas Burner Unit

The Forced Air Gas Burner Trainer, "GBT", designed by EDIBON, is a compact teaching unit with wheels to facilitate its mobility. It represents a controlled gas system that supplies a forced air gas burner. It allows the study of the arrangement,...
View Unit
DOMESTIC GAS SUPPLY EXPERIMENTATION UNIT - GHST
  • GHST
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

GHST

Domestic Gas Supply Experimentation Unit

The Gas Home Supply Trainer, ,GHST,, designed by EDIBON, consists of a teaching unit where the elements normally used on any domestic gas installation are arranged on the front panel of the unit as in a real installation.The unit works with air,...
View Unit
ELECTRICAL INSTALLATIONS IN REFRIGERATION SYSTEMS UNIT - TEIR
  • TEIR
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

TEIR

Electrical Installations in Refrigeration Systems Unit

For this purpose this unit has been designed to teach the students about different circuits and electrical devices associated with the refrigeration field, how to carry out the wirings of these types of installations, how the refrigeration...
View Unit
ELECTRICAL CONNECTION OF REFRIGERANT COMPRESSORS UNIT - TECR
  • TECR
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

TECR

Electrical Connection of Refrigerant Compressors Unit

The Electrical Connection of Refrigerant Compressors Unit, "TECR", includes the electrical elements required for the start and operation of a refrigerant compressor and the necessary safety elements, arranged on a panel in a clear and visible way,...
View Unit
ELECTRICAL FAULTS IN AIR CONDITIONING SYSTEMS UNIT - TEFA
  • TEFA
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

TEFA

Electrical Faults in Air Conditioning Systems Unit

The Electrical Faults in Air Conditioning Systems Unit,"TEFA", is designed in a simple way in order to transmit comprehensible knowledge about how identify electrical faults in air conditioning systems. For this purpose, concepts are included to...
View Unit
HYDRAULIC RADIATOR BALANCING TRAINING UNIT - THBT
  • THBT
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

THBT

Hydraulic Radiator Balancing Training Unit

The Hydraulic Radiator Balancing Training Unit, "THBT", allows the study of the amount of water with which to guarantee that all the radiators of an installation are supplied with sufficient hot water.The hydraulic balancing is carried out by...
View Unit
RADIATORS TRAINING UNIT - RT
  • RT
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

RT

Radiators Training Unit

The Radiators Training Unit, "RT", has been designed to study hot water heating systems. These systems are called that way because they use water as working fluid between the generation system, usually a boiler, and the emitters, such as...
View Unit
HEATING SYSTEM TRAINING UNIT - THST
  • THST
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

THST

Heating System Training Unit

The Heating System Training Unit, "THST", has been designed to study central heating systems. The unit simulates a central heating system. For that purpose, it is made up of four radiators with a thermostatic valve each. This valve controls the...
View Unit
THREE-WAY MIXING VALVE TRAINING UNIT - TEV3V
  • TEV3V
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

TEV3V

Three-Way Mixing Valve Training Unit

The Three-Way Mixing Valve Training Unit, "TEV3V", allows to demonstrate the function of a three-way mixing valve in a hot water heating system. The three-way mixing valve in the heating system regulates the supply water temperature to a heating...
View Unit
FOUR-WAY MIXING VALVE TRAINING UNIT - TEV4V
  • TEV4V
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

TEV4V

Four-Way Mixing Valve Training Unit

The Four-Way Mixing Valve Training Unit, "TEV4V", allows to demonstrate the function of a four-way mixing valve in a hot water heating system. The four-way mixing valve in the heating system regulates the circulation and feed flow temperatures of...
View Unit
SANITARY FITTINGS TRAINING UNIT - TEIS
  • TEIS
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

TEIS

Sanitary Fittings Training Unit

The Sanitary Fittings Training Unit, "TEIS", has been designed by EDIBON for training in the plumbing sector. It consists of an anodized aluminum frame and panels in painted steel in which tests can be carried out with the most common systems of...
View Unit
Ask for information