9.10.- INSTALLATIONS AND MAINTENANCE

The needs of today's society are a challenge for any industry, since they have to be in continuous evolution and renewal to adapt to those needs.

View more

In recent years, as a result of the new industrial revolution or "Industry 4.0", the emergence of the "Industrial Internet of Things" ("IIoT") and the "Smart Factories", that adaptation is possible thanks to the application of the most sophisticated techniques in the design of new facilities or in the renovation of existing ones.

In spite of all these technological advances and the exhaustive controls carried out, it should not be forgotten that any element that take part in the productive process is going to be subjected to a mechanical and electrical wear (efforts, loads, etc.) and its useful life is limited. To avoid catastrophic failures, stoppages in production or any type of process that implies an increase of non-productive times and, therefore, an increase of costs, it is extremely important to carry out a good maintenance of machinery, electrical systems, etc.

Traditionally, only two types of maintenance were considered:

  • Corrective: the fault is solved once it has already occurred.
  • Preventive: periodic review of all those problematic elements and their replacement if required.

These types of maintenance involve very high and unnecessary costs in most cases. Nowadays, thanks to the available technology, it is possible to carry out predictive maintenance consisting of a comprehensive analysis of all those variables that take part in all the components of a system and be able to replace them at the right time.

But, if more control over the failures that can suffer all those mechanical components subject to wear is preferred, there is another type of maintenance, known as proactive maintenance. It goes one step further than the predictive maintenance, looking for the root of the problem.

View Products
Related Materials

INSTALLATIONS AND MAINTENANCE EQUIPMENT

1.- PHYSICS 2.- ELECTRONICS 3.- COMMUNICATIONS 4.- ELECTRICITY 5.- ENERGY 6.- MECHATRONICS & AUTOMATION 7.- MECHANICS 8.- FLUID MECHANICS 9.- THERMODYNAMICS & THERMOTECHNICS 10.- PROCESS CONTROL 11.- CHEMICAL ENGINEERING 12.- FOOD & WATER TECHNOLOGIES 13.- ENVIRONMENT 14.- BIOMEDICAL ENGINEERING LABORATORY ACCESSORIES CUSTOMIZED PILOT PLANTS
9.2.- HEATING, VENTILATION, AIR CONDITIONING AND HOT WATER 9.3.- HEAT PUMPS 9.4.- REFRIGERATION 9.5.- THERMAL HYDRAULIC PIPING SYSTEM 9.6.- HEAT TRANSFER 9.7.- HEAT EXCHANGERS 9.8.- THERMAL MACHINES 9.9.- INTERNAL COMBUSTION ENGINES 9.10.- INSTALLATIONS AND MAINTENANCE 9.1.- FUNDAMENTALS AND BASIC CONCEPTS OF THERMODYNAMICS
9.10.1.- CUTAWAY MODELS 9.10.2.- DETACHABLE MODELS 9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING
Showing 31-37 of 37 item(s)
12 24 36
DRINKING WATER INSTALLATION UNIT - TIAP
  • TIAP
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

TIAP

Drinking Water Installation Unit

The Drinking Water Installation Unit, "TIAP", has been designed to demonstrate domestic water heating from the cold water supply. A typical domestic drinking water system is attached to the front panel of the unit. The unit includes the most...
View Unit
PROTECTION OF DRINKING WATER TRAINING UNIT - TPAP
  • TPAP
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

TPAP

Protection of Drinking Water Training Unit

The Protection of Drinking Water Training Unit, "TPAP", has been designed by EDIBON to study cases in which the drinking water system is contaminated with wastewater. It is specially designed for the training of students in the plumbing sector.The...
View Unit
PIPE CLEANING TRAINING UNIT - TELT
  • TELT
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

TELT

Pipe Cleaning Training Unit

The Pipe Cleaning Training Unit, "TELT", designed by EDIBON, simulates a real house piping system, so original components used in plumbing systems are employed.The objective of this unit is to study the cleaning of pipes from the sanitation...
View Unit
SEWERAGE UNIT - TSID
  • TSID
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

TSID

Sewerage Unit

With the Sewerage Unit, "TSID", tests about a wastewater sanitation system can be made and the flow in a sewage system can be observed.A complete sewage system can be observed with the "TSID" unit. The collection of wastewater from a series of...
View Unit
CIRCULATING PUMPS TRAINING UNIT - TCPT
  • TCPT
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

TCPT

Circulating Pumps Training Unit

The Circulating Pumps Training Unit, "TCPT", designed by EDIBON, is an advanced tool designed to facilitate the study and understanding of the operation of circulation pumps in heating systems and sanitary techniques. This unit allows...
View Unit
EXPANSION VESSEL TRAINING UNIT - TEVT
  • TEVT
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

TEVT

Expansion Vessel Training Unit

The Expansion Vessel Training Unit, "TEVT", is a test unit for sanitary and heating techniques that allows studying the operation of an expansion vessel. It also allows studying the pressure – volume characteristic curve of it. The aim element of...
View Unit
PRESSURE VESSEL AND SAFETY FEATURES TRAINING UNIT - TPVST
  • TPVST
Available
9.10.3.- INSTALLATIONS AND MAINTENANCE TRAINING

TPVST

Pressure Vessel and Safety Features Training Unit

The Pressure Vessel and Safety Features Training Unit, "TPVST", is an experimentation of sanitary and heating techniques unit that allows studying the safety elements of a heating system with a pressure tank. It consists of a circuit of pipes for...
View Unit
Ask for information