Are you a teacher or do you work as an engineering researcher? EDIBON offers courses for teachers and #research staff. Take a look at the course of Fluid Mechanics and learn about #fluids properties. #DiscoverEdibon #Engineering.
AFT/B Fluid Friction in Pipes Unit, with Basic Hydraulics Feed System (FME00/B)
SISTEM INOVATIF
The Fluid Friction in Pipes Unit, with Basic Hydraulics Feed System (FME00/B), "AFT/B", is designed to determine the friction coefficient in pipes of several diameters and roughness, to study the pressure losses in different types of valves and different fittings and to compare different methods to measure the flow.
BERITA TERKAIT
GAMBARAN UMUM
The Fluid Friction in Pipes Unit, with Basic Hydraulics Feed System (FME00/B), "AFT/B", is designed to determine the friction coefficient in pipes of several diameters and roughness, to study the pressure losses in different types of valves and different fittings and to compare different methods to measure the flow.
The unit contains five straight pipe sections made of different materials and with different diameters and roughness. Additionally, a wide range of accessories are included for the study of losses in straight pipes, several types of valves (gate, ball, angle seat, etc.), pipe fittings (in-line strainer, elbows, sudden widening, contraction, etc.).
The different pipe sections, valves and pipe fittings include several pressure measurement points with quick action connections to fit the tubing that is connected to the corresponding pressure measuring device.
With this unit friction pressure losses can be investigated over a wide range of Reynolds numbers, thereby covering the laminar, transitional and turbulent flow regimes. Two water manometric tubes allow to study the pressure losses in the laminar regimen. Two Bourdon manometers allow to obtain the pressure losses in the turbulent regimen. Additionally, it includes (in the Basic Hydraulic Feed System "FME00/B" a flowmeter to measure and to compare measurements of flow with the Venturi tube and the Pitot tube.
The unit includes the Basic Hydraulic Feed System "FME00/B", which incorporates a tank and a centrifugal pump to make water flow in a close circuit and to supply it to the AFT/B unit.
LATIHAN DAN PRAKTEK PEDOMAN
LATIHAN PRAKTIS YANG DIANDAL TERMASUK DALAM PANDUAN
- Determination of pressure loss due to friction in a rough pipe with an internal diameter of 17 mm.
- Determination of pressure loss due to friction in a rough pipe with an internal diameter of 23 mm.
- Determination of pressure loss due to friction in a smooth pipe with an internal diameter of 6.5 mm.
- Determination of pressure loss due to friction in a smooth pipe with an internal diameter of 16.5 mm.
- Determination of pressure loss due to friction in a smooth pipe with an internal diameter of 26.5 mm.
- Study of the influence of the diameter in the pressure loss due to friction in rough pipes.
- Study of the influence of the diameter in the pressure loss due to friction in smooth pipes.
- Study of the influence of the roughness in the pressure loss.
- Determination of the friction coefficient in a rough pipe with an internal diameter of 17 mm.
- Determination of the friction coefficient in a rough pipe with an internal diameter of 23 mm.
- Determination of the friction coefficient in a smooth pipe with an internal diameter of 6.5 mm.
- Determination of the friction coefficient in a smooth pipe with an internal diameter of 16.5 mm.
- Determination of the friction coefficient in a smooth pipe with an internal diameter of 26.5 mm.
- Study of the influence of the diameter in the friction coefficient in rough pipes.
- Study of the influence of the diameter in the friction coefficient in smooth pipes.
- Comparison of the friction coefficient in smooth and rough pipes.
- Determination of pressure loss in an angle-seat valve.
- Determination of pressure loss in a gate valve.
- Determination of pressure loss in a diaphragm valve.
- Determination of pressure loss in a ball valve.
- Comparison of pressure loss in different types of valves.
- Determination of pressure loss in an in-line strainer.
- Determination of pressure loss in a 90° elbow.
- Determination of pressure loss in a double 90° elbow.
- Determination of pressure loss in a 45° elbow.
- Determination of pressure loss in a 45° "T".
- Determination of pressure loss in a symmetrical "Y" branch.
- Determination of pressure loss in a narrowing.
- Determination of pressure loss in a gradual widening.
- Determination of pressure loss in a diaphragm.
- Comparison of pressure loss in the different fittings.
- Measurement of the flow with the Venturi tube.
- Determination of the discharge coefficient, Cd, in the Venturi tube.
- Measurement of the flow with the Pitot tube.
- Determination of the discharge coefficient, Cd, in the Pitot tube.
- Comparison between the flow measured in the Venturi and Pitot tubes.
LEBIH BANYAK LATIHAN PRAKTIS YANG AKAN DILAKUKAN DENGAN UNIT
- Study of the relationship between pressure losses due to fluid friction and the water flow rate.
- Determining the relationship between the pipe friction coefficients and Reynolds number for flow through a pipe with roughened bore.
- Determining of the resistance coefficients for bends, enlargements and contractions.
- Determining of characteristic curves of valves and fittings.
PERALATAN SIMILAR TERSEDIA
8.8.- SISTEM PIPA FLUIDA
AFTC
The Computer Controlled Fluid Friction in Pipes, with Hydraulics Bench (FME00), "AFTC", is designed to determine the friction coefficient in pipes of several diameters and roughness, to study the pressure losses and pressure development in...
8.8.- SISTEM PIPA FLUIDA
AFT
Fluid Friction in Pipes Unit, with Hydraulics Bench (FME00)
The Fluid Friction in Pipes Unit, with Hydraulics Bench (FME00), "AFT", is designed to determine the friction coefficient in pipes of several diameters and roughness, to study the pressure losses in different types of valves and different fittings...
8.8.- SISTEM PIPA FLUIDA
AFT/P
Fluid Friction in Pipes Unit
The Fluid Friction in Pipes Unit, "AFT/P", is designed to determine the friction coefficient in pipes, to study the pressure losses in different types of valves and different fittings and to compare different methods to measure the flow.This unit...
PERALATAN KOMPLEMENTER
8.8.- SISTEM PIPA FLUIDA
AFTC
Computer Controlled Fluid Friction in Pipes, with Hydraulics Bench (FME00)
The Computer Controlled Fluid Friction in Pipes, with Hydraulics Bench (FME00), "AFTC", is designed to determine the friction coefficient in pipes of several diameters and roughness, to study the pressure losses and pressure development in...
8.8.- SISTEM PIPA FLUIDA
AFT
Fluid Friction in Pipes Unit, with Hydraulics Bench (FME00)
The Fluid Friction in Pipes Unit, with Hydraulics Bench (FME00), "AFT", is designed to determine the friction coefficient in pipes of several diameters and roughness, to study the pressure losses in different types of valves and different fittings...
8.8.- SISTEM PIPA FLUIDA
AFT/P
Fluid Friction in Pipes Unit
The Fluid Friction in Pipes Unit, "AFT/P", is designed to determine the friction coefficient in pipes, to study the pressure losses in different types of valves and different fittings and to compare different methods to measure the flow.This unit...
8.8.- SISTEM PIPA FLUIDA
AMTC
Computer Controlled Pipe Network Unit, with Hydraulics Bench (FME00)
The Computer Controlled Pipe Network Unit, with Hydraulics Bench (FME00), "AMTC", consists of a pipe network, a lateral panel where all the elements to test are located and a hydraulics bench, which has all the elements and accessories required...
8.8.- SISTEM PIPA FLUIDA
AMT
Pipe Network Unit, with Hydraulics Bench (FME00)
The Pipe Network Unit, with Hydraulics Bench (FME00), "AMT", consists of a Pipe network, a lateral panel where all the elements to test are located and a hydraulics bench, which has all the elements and accessories required for the unit to work...
8.8.- SISTEM PIPA FLUIDA
AMT/B
Pipe Network Unit, with Hydraulics Bench (FME00/B)
The Pipe Network Unit, without Hydraulics Bench (FME00), "AMT/B", consists of a Pipe network, a lateral panel where all the elements to test are located and a hydraulics bench, which has all the elements and accessories required for the unit to...
8.8.- SISTEM PIPA FLUIDA
AMT/P
Mesh in Pipe Unit
The Mesh in Pipe Unit, "AMT/P", consists of a Pipe network, a lateral panel where all the elements to test are located and a hydraulics bench, which has all the elements and accessories required for the unit to work autonomously.The valves that...
8.8.- SISTEM PIPA FLUIDA
PDCFP
Unit to Study the Pressure Drop of Compressible Fluids in Pipes
The Unit to Study the Pressure Drop of Compressible Fluids in Pipes, "PDCFP", allows the study of the compressible fluid pressure drop, for example the air of a compressor, and the different flow conditions (laminar and turbulent) thanks to the...
8.8.- SISTEM PIPA FLUIDA
EGAC
Computer Controlled Water Hammer Unit
The Computer Controlled Water Hammer Unit, "EGAC", is designed to demonstrate the effects of an instantaneous variation of the speed of a fluid. It is possible to study the water hammer, which is the consequence of a quick change in a fluid speed....
8.7.5.- KOMPRESOR
HFCC
Computer Controlled Flow of Compressible Fluids Unit
The Computer Controlled Flow of Compressible Fluids Unit, "HFCC", allows to study the variation of pressure and density, the speeds of the fluid, the different fluctuations that the fluid presents when fluids across different sections in a pipe,...
8.9.3.- PRAKTIK INSTALASI DAN PEMELIHARAAN
PDDRC
Computer Controlled Unit for Transient Drainage Processes in Storage Reservoirs
The Computer Controlled Unit for Transient Drainage Processes in Storage Reservoirs, "PDDRC", allows to investigate transient drainage processes in storage reservoirs, to simulate a rainwater retention basin and to study the operation of a surge...
9.2.- PEMANASAN, VENTILASI, AC DAN AIR PANAS
TSCAC
Computer Controlled Air Duct Systems Unit
With the Computer Controlled Air Duct Systems Unit, "TSCAC", the user will study the air distribution under different configurations thanks to the supports included with the unit. The user himself will assemble the air ducts using usual elements...