Are you a teacher or do you work as an engineering researcher? EDIBON offers courses for teachers and #research staff. Take a look at the course of Fluid Mechanics and learn about #fluids properties. #DiscoverEdibon #Engineering.
PBSPB Series/Parallel Pumps Bench
SISTEM INOVATIF
The Series/Parallel Pumps Bench, "PBSPB", is designed to demonstrate the operational advantages of parallel or series operation, depending on the required duty.
BERITA TERKAIT
GAMBARAN UMUM
The Series/Parallel Pumps Bench, "PBSPB", is designed to demonstrate the operational advantages of parallel or series operation, depending on the required duty.
This unit consists of two centrifugal pumps, a feed water tank, circulation pipes, regulation valves, three pressure meters and a flow meter.
The centrifugal pumps can operate: alone, coupled in series or in parallel. A three-phase motor activates a pump with possibility of adjustment and measurement of the turn speed as well as of the transmitted mechanic torque, and a single-phase motor activates the other pump.
The pumps are installed in a pipes system, which, as it is a closed circuit, avoids the permanent waste of water during the operation.
By the appropiate positioning of the valves it is possible to connect the pumps individually, in series or in parallel, depending on which test is going to be performed.
LATIHAN DAN PRAKTEK PEDOMAN
LATIHAN PRAKTIS YANG DIANDAL TERMASUK DALAM PANDUAN
- Obtaining of curves H (Q), N (Q), Eff% (Q).
- Obtaining of the map of a centrifugal pump.
- Adimensional study of magnitudes H*, N* and Q*.
- Cavitation test and obtaining of curves NPSHr.
- Series coupling of two pumps with same characteristics.
- Series coupling of two pumps of different characteristics.
- Parallel coupling of two pumps with same characteristics.
- Parallel coupling of two pumps of different characteristics.
- Sensors calibration.
PERALATAN SIMILAR TERSEDIA
8.1.6.- MESIN HIDROLIK: POMPA
FME12
The Series/Parallel Pumps unit, "FME12", designed by EDIBON, allows the study of the coupling between two series/parallel centrifugal pumps, obtaining the characteristic curves as well as the calculation of the water flow rate.The unit consists of...
8.1.6.- MESIN HIDROLIK: POMPA
FME13
Karakteristik Pompa Sentrifugal
The Centrifugal Pump Characteristics, "FME13", designed by EDIBON, allows the study of several centrifugal pump characteristics such as efficiency, series/parallel couplings, etc.The unit has a centrifugal pump with similar characteristics to the...
8.7.1.- POMPA
PBSPC
Computer Controlled Series/Parallel Pumps Bench
The Computer Controlled Series/Parallel Pumps Bench, "PBSPC", is designed to demonstrate the operational advantages of parallel or series operation, depending on the required duty.This unit consists of two centrifugal pumps, a feed water tank,...
PERALATAN KOMPLEMENTER
8.7.1.- POMPA
PBOC
Computer Controlled Multipump Testing Bench (4 types of pumps)
The Computer Controlled Multipump Testing Bench (4 types of pumps), "PBOC", allows the students to study the operating characteristics of several types of pumps. This unit allows to control and to measure the most representative parameters of the...
8.7.1.- POMPA
PB2C
Computer Controlled Multipump Testing Bench (2 types of pumps)
The Computer Controlled Multipump Testing Bench (2 types of pumps), "PB2C", allows the students to study the operating characteristics of the centrifugal and gear pumps. This unit allows to control and to measure the most representative parameters...
8.7.1.- POMPA
PBSPC
Computer Controlled Series/Parallel Pumps Bench
The Computer Controlled Series/Parallel Pumps Bench, "PBSPC", is designed to demonstrate the operational advantages of parallel or series operation, depending on the required duty.This unit consists of two centrifugal pumps, a feed water tank,...
8.7.1.- POMPA
PBCC
Computer Controlled Centrifugal Pump Bench
The Computer Controlled Centrifugal Pump Bench, "PBCC", is a bench-top unit consists of a centrifugal pump computer controlled, a feed water tank, circulation pipes, regulation valves, as well as the enough control elements for the pump...
8.7.1.- POMPA
PBCB
Centrifugal Pump Bench
The Centrifugal Pump Bench, "PBCB", is a bench-top unit consists of a centrifugal pump, a feed water tank, circulation pipes, regulation valves, as well as the enough control elements for the pump experiments: two manometer and a flow sensor.A...
8.7.1.- POMPA
PBEC
Computer Controlled Gear Pump Bench
The Computer Controlled Gear Pump Bench, "PBEC", is a bench-top unit consists of a gear pump computer controlled, a feed water tank, circulation pipes, regulation valves, as well as the enough control elements for the pump experiments: two...
8.7.1.- POMPA
PBAC
Computer Controlled Axial Pump Bench
The Computer Controlled Axial Pump Bench, "PBAC", is designed to study this type of pumps. It is a bench-top unit that consists of a computer controlled axial pump, a water tank and circulation pipes with a flow regulation valve. Besides, it...
8.7.1.- POMPA
PBRC
Computer Controlled Piston Pump Bench
The Computer Controlled Piston Pump Bench, "PBRC", is a bench-top unit that consists of a piston pump, a feed tank, flow meter tank calibrated for taking flow measurements, circulation pipes, manual valves and a solenoid valve, computer...
8.7.3.- TURBIN
HMFAC
Computer Controlled Axial Flow Turbomachines Unit
The Computer Controlled Axial Flow Turbomachines Unit, "HMFAC", allows the study of single-stage axial turbomachines, with interchangeable vanes for the study of both a pump and a turbine.The main part of the unit is the axial turbomachine...