On December 1st, the Repair Course for Small Laboratory Equipment, taught by our engineers at the EDIBON facilities, was completed, lasting 4 days.
The attendees, (Laboratory technicians and maintenance of the Rey Juan Carlos University of Madrid) had the opportunity to perform multiple...
TECNEL/B Unit Pembelajaran dengan Komputer Kontrol untuk Belajar Elektronika Daya Dasar (tanpa IGBTS)
SISTEM INOVATIF
The TECNEL/B is a Unit with Computer Control and Data Acquisition System designed to study the basis of Power Electronics.
Ekspansi
BERITA TERKAIT
GAMBARAN UMUM
The Computer Controlled Basic Teaching Unit for the Study of Power Electronics (no IGBTS). (Converters: AC/DC+AC/AC), "TECNEL/B", is a unit with Computer Control and Data Acquisition System designed to study the basis of Power Electronics. It allows students to study AC/DC, AC/AC converters.
This Computer Controlled Unit is supplied with the EDIBON Computer Control System (SCADA), and includes: The unit itself + a Data Acquisition Board + Computer Control, Data Acquisition and Data Management Software Packages, for controlling the process and all parameters involved in the process.
LATIHAN DAN PRAKTEK PEDOMAN
LATIHAN PRAKTIS YANG DIANDAL TERMASUK DALAM PANDUAN
- Single phase half-wave rectifier with load R.
- Single phase half-wave rectifier with load R-L.
- Single-phase half-wave rectifier with R-L load with free wheeling diode (FWD).
- Single-phase full-wave rectifier.
- Three-phase half-wave uncontrolled rectifier.
- Three-phase full-wave uncontrolled rectifier.
- Single-phase half-wave controlled rectifier.
- Single-phase full-wave controlled rectifier.
- Single-phase full-wave controlled rectifier with a DC motor.
- Three-phase full-wave completely controlled.
- Single-phase semi-controlled rectifier.
- Three-phase full-wave semi-controlled rectifier.
- Alternating regulators: R and R-L load.
LEBIH BANYAK LATIHAN PRAKTIS YANG AKAN DILAKUKAN DENGAN UNIT
- Many students view results simultaneously. To view all results in real time in the classroom by means of a projector or an electronic whiteboard.
- Open Control, Multicontrol and Real Time Control. This unit allows intrinsically and/or extrinsically to change the span, gains, proportional, integral, derivative parameters, etc. in real time.
- The Computer Control System with SCADA allows a real industrial simulation.
- This unit is totally safe as uses mechanical, electrical/electronic, and software safety devices.
- This unit can be used for doing applied research.
- This unit can be used for giving training courses to Industries even to other Technical Education Institutions.
- Several other exercises can be done and designed by the user.
PERALATAN SIMILAR TERSEDIA
6.1.2.2.- ELEKTRONIK TENAGA DAN ELEKTRONIK INDUSTRI
TECNEL
The Computer Controlled Teaching Unit for the Study of Power Electronics (with IGBTS), "TECNEL" is a unit with Computer Control and Data Acquisition System designed to study the basis of Power Electronics. It allows students to study AC/DC, DC/AC,...
5.1.3.2.- KEKUATAN TRANSMISI
AEL-SVC
Aplikasi Pengendalian Tegangan dengan SVCs dalam Sistem Transmisi, Dikendalikan dari Komputer (PC)
The Computer Controlled Voltage Control with SVCs in Transmission Systems Application, "AEL-SVC", has been designed by EDIBON to study the most important applications based on thyristor controlled reactor (TCR) and thyristor switched capacitor...
PERALATAN KOMPLEMENTER
6.1.2.2.- ELEKTRONIK TENAGA DAN ELEKTRONIK INDUSTRI
TECNEL
Unit Pembelajaran dengan Komputer Kontrol untuk Belajar Elektronika Daya (dengan IGBTS)
The Computer Controlled Teaching Unit for the Study of Power Electronics (with IGBTS), "TECNEL" is a unit with Computer Control and Data Acquisition System designed to study the basis of Power Electronics. It allows students to study AC/DC, DC/AC,...
6.1.2.2.- ELEKTRONIK TENAGA DAN ELEKTRONIK INDUSTRI
SERIN/CC
Unit Pelatihan Industri Lanjut dengan Komputer Kontrol Sistem Servo (motor DC)
The Computer Controlled Advanced Industrial Servosystem Unit (for DC Motors), "SERIN/CC", allows different practices related to servomotors to be carried out. The unit has different modules to develop different experiments. The modules included in...
6.1.2.2.- ELEKTRONIK TENAGA DAN ELEKTRONIK INDUSTRI
SERIN/CCB
Unit Pelatihan Sistem Servo Dasar (motor DC)
The Servosystems Basic Unit for DC Motors, "SERIN/CCB", is an unit whose goal is studying low power servo systems. It is a low power DC motor speed control trainer that has a breakdown simulator.This unit is a basic version of the Computer...
6.1.2.2.- ELEKTRONIK TENAGA DAN ELEKTRONIK INDUSTRI
SERIN/CA
Unit Pelatihan Industri Lanjut dengan Komputer Kontrol Sistem Servo (motor AC)
The "SERIN/CA" trainer consists on a Control Interface Box connected to a three-phase motor and to a computer (computer not included). The control interface has a resolver for three-phase motors that controls the speed, position and currentof the...
5.3.3.- ENERGI ANGIN
AEL-WPP
Aplikasi Pembangkit Listrik Tenaga Angin dengan Generator Induksi Ganda
The Wind Power Plants with Double Feed Induction Generator Application, "AEL-WPP", is used to investigate the design and operation of modern wind power stations. The "AEL-WPP" consists of a prime motor that moves a double-feed induction generator...
5.3.3.- ENERGI ANGIN
AEL-WPPIC
Aplikasi Pembangkit Listrik Tenaga Angin dengan Generator Induksi, Dikendalikan dari Komputer (PC)
The Computer Controlled Wind Power Plants Application with Induction Generator, "AEL-WPPIC", has been designed by EDIBON to study of the main characteristics and behavior of the induction generators used in wind turbines which inject the generated...
5.3.3.- ENERGI ANGIN
AEL-WPPI
Aplikasi Pembangkit Listrik Tenaga Angin dengan Generator Induksi
The Wind Power Plants with Induction Generator Application, "AEL-WPPI", has been developed by EDIBON to study the wind turbines electrical performance with three-phase induction generators of squirrel cage that inject power in the network.Wind...
2.4.3.- DAYA ELEKTRONIK
AE-PEC
Aplikasi Elektronika Daya Lanjutan, Dikendalikan oleh Komputer (PC)
The Computer Controlled Advanced Power Electronics Application, "AE-PEC", includes various modules that allow exploration of different aspects of power electronics. The modular design of this application ensures flexibility and adaptability to...
6.1.2.2.- ELEKTRONIK TENAGA DAN ELEKTRONIK INDUSTRI
AEL-SERIN/CA-1KW
Aplikasi Servo Motor Industri AC 1 Kw
The 1 kW AC Industrial Servomotor Application, "AEL-SERIN/CA-1KW", has been designed to study the working principle and control of industrial servomotors. The "AEL-SERIN/CA-1KW" allows the user to acquire knowlegde and experience in the control of...