AFTC コンピューター制御導管内流体摩擦実験装置（水圧ベンチFME00付）

8.8.- 流体配管システム
COMPUTER CONTROLLED FLUID FRICTION IN PIPES, WITH HYDRAULICS BENCH (FME00) - AFTC

Unit: AFTC. Computer Controlled Fluid Friction in Pipes, with Hydraulics Bench (FME00)

COMPUTER CONTROLLED FLUID FRICTION IN PIPES, WITH HYDRAULICS BENCH (FME00) - AFTC

Complete AFTC unit

COMPUTER CONTROLLED FLUID FRICTION IN PIPES, WITH HYDRAULICS BENCH (FME00) - AFTC

Unit details

COMPUTER CONTROLLED FLUID FRICTION IN PIPES, WITH HYDRAULICS BENCH (FME00) - AFTC

AFTC/CIB. Control Interface Box: The Control Interface Box is part of the SCADA system

COMPUTER CONTROLLED FLUID FRICTION IN PIPES, WITH HYDRAULICS BENCH (FME00) - AFTC

Process diagram and unit elements allocation

COMPUTER CONTROLLED FLUID FRICTION IN PIPES, WITH HYDRAULICS BENCH (FME00) - AFTC

AFTC/SOF. AFTC Software. Main Screen

COMPUTER CONTROLLED FLUID FRICTION IN PIPES, WITH HYDRAULICS BENCH (FME00) - AFTC
COMPUTER CONTROLLED FLUID FRICTION IN PIPES, WITH HYDRAULICS BENCH (FME00) - AFTC
COMPUTER CONTROLLED FLUID FRICTION IN PIPES, WITH HYDRAULICS BENCH (FME00) - AFTC
COMPUTER CONTROLLED FLUID FRICTION IN PIPES, WITH HYDRAULICS BENCH (FME00) - AFTC
COMPUTER CONTROLLED FLUID FRICTION IN PIPES, WITH HYDRAULICS BENCH (FME00) - AFTC
COMPUTER CONTROLLED FLUID FRICTION IN PIPES, WITH HYDRAULICS BENCH (FME00) - AFTC

革新的なシステム

The Computer Controlled Fluid Friction in Pipes, with Hydraulics Bench (FME00), "AFTC", is designed to determine the friction coefficient in pipes of several diameters and roughness, to study the pressure losses and pressure development in different types of valves and fittings and to compare different methods to measure the flow.

一般的な説明を表示
カタログ カタログ
コンテストの仕様
リクエスト情報

拡張

ICAI

インタラクティブなコンピュータ支援教育ソフトウェア
FSS

故障シミュレーションシステム
PLCHMI

HMIを使用したローカル/リモートIIoT制御と監視
ELK

EDIBONソフトウェア開発キット、NI LabVIEW™による動作
ESN

EDIBON Scada-Netシステム
ECL

EDIBON遠隔教育

研究室

13TV
 技術教育・職業教育環境実験室
13HE
 高等教育環境研究室
11PTC
 石油研修センター研究室
8TV
 技術教育・職業教育のための流体力学研究室
8HE
 高等教育用流体力学研究室

関連ニュース

EDIBON and its commitment to European Skills
EDIBON and its commitment to European Skills
At EDIBON, we are committed to strengthening skills as a strategic pillar for the competitiveness and social well-being of the European Union. Proper training not only boosts the economy but also enables individuals to fully participate in society and democracy.
続きを読む
Setting up at University of the Punjab, Pakistan.
Setting up at University of the Punjab, Pakistan.
Our local representative just completed an installation at University of the Punjab, Pakistan. There we installed equipment like the HCMP; AFTC; PBSPC; HVCC; EMLS; LFFC; LIFLUBA; FME00; TMTC; TSTCC; EESTC; EESFC; EE-KIT; EEEC; EEF; EBEC; EBDC; TTEC; SFU; RETU, among others. Our cutting-edge...
続きを読む
Setting up at Texas A&M University in Qatar
Setting up at Texas A&M University in Qatar
We have returned to Texas AandM University in Qatar where we installed three of our chemical engineering and fluid mechanics units. At EDIBON we always offer the best quality to our customers. But, in addition, if you need support, you can be sure that we will help you with our after-sales service.
続きを読む
Setting up at University of Valencia
Setting up at University of Valencia
We want to show you the new installation that we carry out at the University of Valencia, specifically in the Chemical Engineering Department of the Higher Technical School of Engineering. We have installed our FLUID FRICTION IN PIPES UNIT, WITH BASIC HYDRAULICS FEED SYSTEM (FME00/B), designed to...
続きを読む
Set up at Universidad de Huelva (Spain)
Set up at Universidad de Huelva (Spain)
Glad to announce one of our latest set-ups at Universidad de Huelva, with a complete installation for the Agroforestry Science department's students and researchers, including AFTC, QRCC, TFRC or MCEN, among others. We are proud to contribute in the technical preparation of future agroforestry...
続きを読む
Installation at TAMU - Texas A&M University
Installation at TAMU - Texas A&M University
This month we travelled to Texas A&M University to participate in the Petroleum engineering program (Qatar Tamu) where we installed three units: Computer Controlled Horizontal Three-phase Separator (HTSC), Computer Controlled Vertical Three-phase Separator (VTSC) and the Computer Controlled Fluid...
続きを読む
NEW Fluid Mechanics Course
NEW Fluid Mechanics Course
Are you a teacher or do you work as an engineering researcher? EDIBON offers courses for teachers and #research staff. Take a look at the course of Fluid Mechanics and learn about #fluids properties. #DiscoverEdibon #Engineering.
続きを読む

概要

The Computer Controlled Fluid Friction in Pipes, with Hydraulics Bench (FME00), "AFTC", is designed to determine the friction coefficient in pipes of several diameters and roughness, to study the pressure losses and pressure development in different types of valves and fittings and to compare different methods to measure the flow.

The unit contains six horizontal straight pipe sections made of different materials and with different diameters and roughness to study their influence in the pressure losses.

Additionally, a wide range of accessories are included for the study of losses in straight pipes, several types of valves (gate, ball, angle seat, etc.), pipe fittings (mesh filter, elbows, sudden widening, contraction, etc.) and measuring elements (Venturi tube, Pitot tube, orifice plate flowmeter, flow measuring nozzles, etc.).

Some of the measuring elements, like the Venturi tube, Pitot tube, etc., are transparent to observe their function.

The different pipe sections, valves and pipe fittings include several pressure measurement points with quick action connections to fit the tubing that is connected to the corresponding pressure measuring device.

The sections can be exchanged without tools.

With this unit pressure losses can be investigated over a wide range of Reynolds numbers, thereby covering the laminar, transitional and turbulent flow regime. Two water manometric tubes and two displacement sensors allow to study the pressure losses in the laminar regime.

Two pressure sensors allow to obtain the pressure losses in the turbulent regimen. Additionally, it includes a flow sensor to measure and to compare measurements of flow with the Venturi tube and the Pitot tube.

Annular chamber shaped measuring points are located around the measuring elements for an accurate pressure measurement.

The unit includes the Hydraulics Bench (FME00), which incorporates a sump tank and a centrifugal pump to make water flow in a close circuit and to supply the "AFTC" unit, allowing an independent operation of the unit.

A flow sensor measures the flow impelled by the pump.

This Computer Controlled Unit is supplied with the EDIBON Computer Control System (SCADA), and includes: The unit itself + a Control Interface Box + a Data Acquisition Board + Computer Control, Data Acquisition and Data Management Software Packages, for controlling the process and all parameters involved in the process.

演習と指導の慣行

マニュアルに含まれるガイド付き実習

  1. Determination of pressure loss due to friction in a rough pipe with an internal diameter of 17 mm.
  2. Determination of pressure loss due to friction in a rough pipe with an internal diameter of 23 mm.
  3. Determination of pressure loss due to friction in a smooth pipe with an internal diameter of 6.5 mm.
  4. Determination of pressure loss due to friction in a smooth pipe with an internal diameter of 16.5 mm.
  5. Determination of pressure loss due to friction in a smooth pipe with an internal diameter of 26.5 mm.
  6. Study of the influence of the diameter in the pressure loss due to friction in rough pipes.
  7. Study of the influence of the diameter in the pressure loss due to friction in smooth pipes.
  8. Study of the influence of the roughness in the pressure loss.
  9. Determination of the friction coefficient in a rough pipe with an internal diameter of 17 mm.
  10. Determination of the friction coefficient in a rough pipe with an internal diameter of 23 mm.
  11. Determination of the friction coefficient in a smooth pipe with an internal diameter of 6.5 mm.
  12. Determination of the friction coefficient in a smooth pipe with an internal diameter of 16.5 mm.
  13. Determination of the friction coefficient in a smooth pipe with an internal diameter of 26.5 mm.
  14. Study of the influence of the diameter in the friction coefficient in rough pipes.
  15. Study of the influence of the diameter in the friction coefficient in smooth pipes.
  16. Comparison of the friction coefficient in smooth and rough pipes.
  17. Determination of pressure loss in an angle-seat valve.
  18. Determination of pressure loss in a gate valve.
  19. Determination of pressure loss in a diaphragm valve.
  20. Determination of pressure loss in a ball valve.
  21. Comparison of pressure loss in different types of valves.
  22. Determination of pressure loss in an in-line strainer.
  23. Determination of pressure loss in a 90° elbow.
  24. Determination of pressure loss in a double 90° elbow.
  25. Determination of pressure loss in a 45° elbow.
  26. Determination of pressure loss in a 45° "T".
  27. Determination of pressure loss in a symmetrical "Y" branch.
  28. Determination of pressure loss in a narrowing.
  29. Determination of pressure loss in a gradual widening.
  30. Determination of pressure loss in a diaphragm.
  31. Comparison of pressure loss in the different fittings.
  32. Measurement of the flow with the Venturi tube.
  33. Determination of the discharge coefficient, Cd, in the Venturi d tube.
  34. Measurement of the flow with the Pitot tube.
  35. Determination of the discharge coefficient, Cd, in the Pitot tube.
  36. Comparison between the flow measured in the Venturi and Pitot tubes.
  37. Sensors calibration.

より実用的な練習をして、ユニットを完成させる

  1. Study of the relationship between pressure losses due to fluid friction and the water flow rate.
  2. Determining the relationship between the pipe friction coefficients and Reynolds number for flow through a pipe with roughened bore.
  3. Determining of the resistance coefficients for bends, enlargements and contractions.
  4. Determining of characteristic curves of valves and fittings.

Other possibilities to be done with this Unit:

  1. Many students view results simultaneously. To view all results in real time in the classroom by means of a projector or an electronic whiteboard.
  2. Open Control, Multicontrol and Real Time Control. This unit allows intrinsically and/or extrinsically to change the span, gains, proportional, integral, derivative parameters, etc, in real time.
  3. The Computer Control System with SCADA and PID Control allow a real industrial simulation.
  4. This unit is totally safe as uses mechanical, electrical and electronic, and software safety devices.
  5. This unit can be used for doing applied research.
  6. This unit can be used for giving training courses to Industries even to other Technical Education Institutions.
  7. Control of the AFTC unit process through the control interface box without the computer.
  8. Visualization of all the sensors values used in the AFTC unit process.
  9. By using PLC-PI additional 19 more exercises can be done.
  10. Several other exercises can be done and designed by the user.

含まれるアイテム

利用可能な類似の機器

FLUID FRICTION IN PIPES UNIT - AFT/P
  • AFT/P
Available
8.8.- 流体配管システム
AFT/P
導管内流体摩擦実験装置
The Fluid Friction in Pipes Unit, "AFT/P", is designed to determine the friction coefficient in pipes, to study the pressure losses in different types of valves and different fittings and to compare different methods to measure the flow.This unit...
ユニットを見る

品質

アフターサービス

リクエスト情報