SSM Unit to Study Stress on a Membrane

7.1.6.- 構造メカニズム 14.1.6.- 構造メカニズム

革新的なシステム

The Unit to Study Stress on a Membrane, "SSM", designed by EDIBON, allows the study of stresses and deformations in a thin disc or membrane subjected to different compressive stresses.

一般的な説明を表示

カタログ

コンテストの仕様

拡張

ICAI

インタラクティブなコンピュータ支援教育ソフトウェア

概要

The Unit to Study Stress on a Membrane, "SSM", designed by EDIBON, allows the study of stresses and deformations in a thin disc or membrane subjected to different compressive stresses.

The main element of the equipment is a thin disc or membrane that is subjected to pressure and has eight strain gauges attached to its surface that allow the recording of the deformations produced.

A hydraulic system generates the pressure by means of a cylinder and a piston, which is measured by means of a manometer.

In addition, it is also possible to measure the deflection produced in the disc or membrane by means of a dial gauge which can be moved along the entire length of the thin disc. Curvature can be measured at any radius.

演習と指導の慣行

マニュアルに含まれるガイド付き実習

Measurement of radial and shear stresses with strain gauges.
Measurement of deflections with dial gauges.
Calculation of radial and shear stresses from the measured deflections.
Study of the direction of principal stress.
Study of deformation

補完的な機器

UNIT FOR STUDYING FORCES IN A JIB CRANE - MFPG

MFPG

Available

7.1.6.- 構造メカニズム

MFPG

ジブクレーンフォース測定実験装置

The Unit for studying Forces in a Jib Crane, "MFPG", is designed to study the tensile and compressive forces in a planar central force system based on the example of a crane jib.The unit represents a planar central force system in which multiple...

Available

7.1.6.- 構造メカニズム

MVS

サスペンションブリッジ実験装置

The Suspension Bridge Unit, "MVS", has been meticulously designed by EDIBON to explore the dynamics of stresses in a suspension bridge system. This unit simulates a suspension bridge using a deck and two parallel main cables, allowing students to...

MARP

Available

7.1.6.- 構造メカニズム

MARP

パラボラアーチ実験装置

The Parabolic Arch Unit "MARP" contains a pre-shaped articulated arch, which can be subjected to point or evenly distributed loads by means of seven uniformly distributed cables (cords) with hangers.One support of the arch is fixed whereas the...

MART

Available

7.1.6.- 構造メカニズム

MART

3ヒンジアーチ実験装置

The Three-Hinged Arch Unit "MART" allows the student to become familiar with three-hinged arches, to calculate the bearing forces (for point load, for uniformly distributed load and for moving load), to investigate the influence of the load on the...

UNIT FOR STUDYING FORCES IN A SIMPLE BAR STRUCTURE - MFBS

MFBS

Available

7.1.6.- 構造メカニズム

MFBS

単純棒構造における応力測定実験装置

The Unit for Studying Forces in a Simple Bar Structure, "MFBS", designed by EDIBON allows the study of forces acting on a simple truss when is subjected to a point load in one of the nodes that make up the structure.It consists of a group of five...

UNIT FOR STUDYING FORCES IN DIFFERENT SINGLE PLANE TRUSSES - MFCS1

MFCS1

Available

7.1.6.- 構造メカニズム

MFCS1

多様単平面トラスにおける応力測定実験装置

The Unit for studying Forces in Different Single Plane Trusses, "MFCS1", allows the measurement of the bar forces in various single plane trusses, the study of the dependency on the external force and the comparison of the experimental bar forces...

UNIT FOR STUDYING FORCES IN AN OVERDETERMINATE TRUSS - MFCS2

MFCS2

Available

7.1.6.- 構造メカニズム

MFCS2

多元トラスにおける応力測定実験装置

The Unit for studying Forces in an Overdeterminate Truss, "MFCS2", allows the measurement of the bar forces in a statically determinate truss and in a statically overdeterminate truss, the study of the distribution of forces in the single plane...

UNIT FOR STUDYING DEFORMATION OF TRUSSES - MFCS3

MFCS3

Available

7.1.6.- 構造メカニズム

MFCS3

トラスひずみ測定実験装置

The Unit for studying Deformation of Trusses, "MFCS3", allows the measurement of the stresses in the bars in different types of trusses, and the study of the dependence of the external force and the comparison of the experimental forces in the...

MCPG

Available

7.1.6.- 構造メカニズム

MCPG

Thick Walled Cylinder Unit

In the Thick-Walled Cylinder Unit, "MCPG", the stresses are determined through the measurement of the strains produced on the surface. These strains are measured by strain gauges.The thick-walled vessel consists of an aluminum cylinder of length...

Available

7.1.6.- 構造メカニズム

MFL

2ピンアーチ実験装置

The Two Hinged Arch Unit, "MFL", designed by EDIBON allows to study the response of an arched beam when an external load is applied on it.The arch is supported on two supports, a fixed one and a movable one. The displacement and horizontal...

Available

7.1.6.- 構造メカニズム

MPO

ポータルフレーム実験装置

The Portal Frame Unit, "MPO", designed by EDIBON, allows for precise measurements of vertical and horizontal deflection in an embedded rectangular portal frame. By applying various loads with specific weights, changes in the portal frame’s...

Available

7.1.6.- 構造メカニズム

STH

Stress Hypotheses Unit

The Stress Hypotheses Unit, "STH", allows the study and testing of stress hypotheses by applying loads in different directions on a test specimen point and measuring the deformations produced.Normal and shear stresses are applied, avoiding...

品質

アフターサービス

その他の情報については, お問い合わせください

SSM Unit to Study Stress on a Membrane

革新的なシステム

拡張

関連ニュース

概要

演習と指導の慣行

マニュアルに含まれるガイド付き実習

補完的な機器

品質

アフターサービス