MINI-EEEC 计算机控制风力发电的基本设备

COMPUTER CONTROLLED WIND ENERGY BASIC UNIT - MINI-EEEC
COMPUTER CONTROLLED WIND ENERGY BASIC UNIT - MINI-EEEC
COMPUTER CONTROLLED WIND ENERGY BASIC UNIT - MINI-EEEC
COMPUTER CONTROLLED WIND ENERGY BASIC UNIT - MINI-EEEC
COMPUTER CONTROLLED WIND ENERGY BASIC UNIT - MINI-EEEC
COMPUTER CONTROLLED WIND ENERGY BASIC UNIT - MINI-EEEC
COMPUTER CONTROLLED WIND ENERGY BASIC UNIT - MINI-EEEC
COMPUTER CONTROLLED WIND ENERGY BASIC UNIT - MINI-EEEC
COMPUTER CONTROLLED WIND ENERGY BASIC UNIT - MINI-EEEC
COMPUTER CONTROLLED WIND ENERGY BASIC UNIT - MINI-EEEC
COMPUTER CONTROLLED WIND ENERGY BASIC UNIT - MINI-EEEC
COMPUTER CONTROLLED WIND ENERGY BASIC UNIT - MINI-EEEC

相關新聞

一般說明

The Computer Controlled Wind Energy Basic Unit, "MINI-EEEC", is a small-scale unit designed to study wind energy and the influence of some factors on its generation.

This unit consists of a transparent tunnel, a wind turbine with rotor to place up to six blades and a computer controlled variable speed axial fan.

The air speed is varied by changing the rotational speed of the axial fan and a sensor allows for measuring that air velocity.

This fan generates the required air flow to make the rotor of the wind energy unit work. The generator converts the kinetic energy of the rotor into electric energy. The rotational speed of the wind turbine can be measured with a sensor.

The unit includes a DC load module with LEDs, a rheostat, a DC motor, a load selector and switches to select the type of load. Thus, the wind turbine may work in open circuit or connected to LEDS, to a rheostat or to a DC motor.

A voltage and current sensor measures the voltage and current provided by the wind turbine in order to determine the power.

This Computer Controlled Unit is supplied with the EDIBON Computer Control System (SCADA), and includes: The unit itself + a Control Interface Box + a Data Acquisition Board + Computer Control, Data Acquisition and Data Management Software Packages, for controlling the process and all parameters involved in the process.

練習和指導練習

手册中包含的指导实践练习

  1. Study of the aerogenerator operation depending on the wind speed variation.
  2. Determination of the aerogenerator characteristic parameters.
  3. Study of the differences in the operation by using the three available blades'configurations (aerogenerator with six, three or two blades).
  4. Study of the influence of the load variation in the aerogenerator.
  5. Study of voltage, power and current.
  6. Experimental determination of efficiency.
  7. Study of the power generated by the aerogenerator depending on the wind speed.
  8. Study of the power generated by the aerogenerator depending on the number of blades.
  9. Determination of the wind energy measurement.
  10. Study of the characteristic curve of the aerogenerator at constant wind speed.
  11. Study of the characteristic curve of the aerogenerator at constant revolutions.
  12. Study of the DC loads connection.
  13. Sensors calibration.

与该单位进行更多实际操作

  1. Many students view results simultaneously. To view all results in real time in the classroom by means of a projector or an electronic whiteboard.
  2. Open Control, Multicontrol and Real Time Control. This unit allows intrinsically and/or extrinsically to change the span, gains, proportional, integral, derivative parameters, etc, in real time.
  3. The Computer Control System with SCADA allows a real industrial simulation.
  4. This unit is totally safe as uses mechanical, electrical/electronic, and software safety devices.
  5. This unit can be used for doing applied research.
  6. This unit can be used for giving training courses to Industries even to other Technical Education Institutions.
  7. Control of the MINI-EEEC unit process through the control interface box without the computer.
  8. Visualization of all the sensors values used in the MINI-EEEC unit process.
  9. By using PLC-PI additional 19 more exercises can be done.
  10. Several other exercises can be done and designed by the user.

可用的类似设备

質量

售後服務

要求信息